lkml.org 
[lkml]   [2017]   [Jul]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64
Date
Banana Pi M64 board uses an AXP803 PMIC.

Enable the PMIC and its regulators.

As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v2:
- Changed vdd-cpux constraints.
- Added vcc-1v2-hsic regulator.

.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 122 +++++++++++++++++++--
1 file changed, 112 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index a4a7b9cb59b9..ec72ca8c8b30 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -59,13 +59,6 @@
chosen {
stdout-path = "serial0:115200n8";
};
-
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
};

&ehci1 {
@@ -77,6 +70,7 @@
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <&reg_dc1sw>;
status = "okay";
};

@@ -100,7 +94,7 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&reg_vcc3v3>;
+ vmmc-supply = <&reg_dcdc1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
cd-inverted;
disable-wp;
@@ -111,7 +105,8 @@
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- vmmc-supply = <&reg_vcc3v3>;
+ vmmc-supply = <&reg_dldo2>;
+ vqmmc-supply = <&reg_dldo4>;
bus-width = <4>;
non-removable;
status = "okay";
@@ -120,7 +115,7 @@
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
- vmmc-supply = <&reg_vcc3v3>;
+ vmmc-supply = <&reg_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
@@ -131,6 +126,113 @@
status = "okay";
};

+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+ regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
--
2.13.0
\
 
 \ /
  Last update: 2017-07-25 14:52    [W:0.498 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site