lkml.org 
[lkml]   [2017]   [Mar]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [linux-sunxi] [PATCH v2 08/12] ARM: dts: sun8i: restore the inclusion of ccu headers in V3s DTSI
Hi,

On Sun, Mar 5, 2017 at 9:37 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> When the V3s support patchset is applied, CCU headers and V3s DTSI went
> into different trees, so the CCU inclusion is removed in the DTSI.
>
> Add back them.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> arch/arm/boot/dts/sun8i-v3s.dtsi | 67 ++++++++++++++++++++--------------------
> 1 file changed, 34 insertions(+), 33 deletions(-)
>
> diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
> index 71075969e5e6..b3f8b7f9c0bb 100644
> --- a/arch/arm/boot/dts/sun8i-v3s.dtsi
> +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
> @@ -40,6 +40,8 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> +#include <dt-bindings/clock/sun8i-v3s-ccu.h>
> +#include <dt-bindings/reset/sun8i-v3s-ccu.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>

Please sort alphabetically. Or if you want, put the sunxi specific headers
in a separate group, separated by an empty line from the arm-gic one.

>
> / {
> @@ -55,7 +57,7 @@
> compatible = "arm,cortex-a7";
> device_type = "cpu";
> reg = <0>;
> - clocks = <&ccu 14>;
> + clocks = <&ccu CLK_CPU>;
> };
> };
>
> @@ -96,15 +98,15 @@
> mmc0: mmc@01c0f000 {
> compatible = "allwinner,sun7i-a20-mmc";
> reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu 22>,
> - <&ccu 45>,
> - <&ccu 47>,
> - <&ccu 46>;
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> clock-names = "ahb",
> "mmc",
> "output",
> "sample";
> - resets = <&ccu 7>;
> + resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> @@ -115,15 +117,15 @@
> mmc1: mmc@01c10000 {
> compatible = "allwinner,sun7i-a20-mmc";
> reg = <0x01c10000 0x1000>;
> - clocks = <&ccu 23>,
> - <&ccu 48>,
> - <&ccu 50>,
> - <&ccu 49>;
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> clock-names = "ahb",
> "mmc",
> "output",
> "sample";
> - resets = <&ccu 8>;
> + resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> @@ -134,15 +136,15 @@
> mmc2: mmc@01c11000 {
> compatible = "allwinner,sun7i-a20-mmc";
> reg = <0x01c11000 0x1000>;
> - clocks = <&ccu 24>,
> - <&ccu 51>,
> - <&ccu 53>,
> - <&ccu 52>;
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> clock-names = "ahb",
> "mmc",
> "output",
> "sample";
> - resets = <&ccu 9>;
> + resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
> @@ -153,8 +155,8 @@
> usb_otg: usb@01c19000 {
> compatible = "allwinner,sun8i-h3-musb";
> reg = <0x01c19000 0x0400>;
> - clocks = <&ccu 29>;
> - resets = <&ccu 17>;
> + clocks = <&ccu CLK_BUS_OTG>;
> + resets = <&ccu RST_BUS_OTG>;
> interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> interrupt-names = "mc";
> phys = <&usbphy 0>;
> @@ -169,9 +171,9 @@
> <0x01c1a800 0x4>;
> reg-names = "phy_ctrl",
> "pmu0";
> - clocks = <&ccu 56>;
> + clocks = <&ccu CLK_USB_PHY0>;
> clock-names = "usb0_phy";
> - resets = <&ccu 0>;
> + resets = <&ccu RST_USB_PHY0>;
> reset-names = "usb0_reset";
> status = "disabled";
> #phy-cells = <1>;
> @@ -198,7 +200,7 @@
> reg = <0x01c20800 0x400>;
> interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
> + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> clock-names = "apb", "hosc", "losc";
> gpio-controller;
> #gpio-cells = <3>;
> @@ -213,6 +215,7 @@
> uart0_pins_a: uart0@0 {
> pins = "PB8", "PB9";
> function = "uart0";
> + bias-pull-up;

This is an unrelated change. Please split it out. On the other hand,
if the board has proper external pull-ups, you might not need this.

Otherwise,

Acked-by: Chen-Yu Tsai <wens@csie.org>

> };
>
> mmc0_pins_a: mmc0@0 {
> @@ -244,8 +247,8 @@
> interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> reg-shift = <2>;
> reg-io-width = <4>;
> - clocks = <&ccu 40>;
> - resets = <&ccu 49>;
> + clocks = <&ccu CLK_BUS_UART0>;
> + resets = <&ccu RST_BUS_UART0>;
> status = "disabled";
> };
>
> @@ -255,8 +258,8 @@
> interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> reg-shift = <2>;
> reg-io-width = <4>;
> - clocks = <&ccu 41>;
> - resets = <&ccu 50>;
> + clocks = <&ccu CLK_BUS_UART1>;
> + resets = <&ccu RST_BUS_UART1>;
> status = "disabled";
> };
>
> @@ -266,8 +269,8 @@
> interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> reg-shift = <2>;
> reg-io-width = <4>;
> - clocks = <&ccu 42>;
> - resets = <&ccu 51>;
> + clocks = <&ccu CLK_BUS_UART2>;
> + resets = <&ccu RST_BUS_UART2>;
> status = "disabled";
> };
>
> @@ -275,10 +278,8 @@
> compatible = "allwinner,sun6i-a31-i2c";
> reg = <0x01c2ac00 0x400>;
> interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu 38>;
> - resets = <&ccu 46>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> + clocks = <&ccu CLK_BUS_I2C0>;
> + resets = <&ccu RST_BUS_I2C0>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -288,8 +289,8 @@
> compatible = "allwinner,sun6i-a31-i2c";
> reg = <0x01c2b000 0x400>;
> interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu 39>;
> - resets = <&ccu 47>;
> + clocks = <&ccu CLK_BUS_I2C1>;
> + resets = <&ccu RST_BUS_I2C1>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> --
> 2.11.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.

\
 
 \ /
  Last update: 2017-03-06 06:55    [W:0.034 / U:1.492 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site