lkml.org 
[lkml]   [2017]   [Dec]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 5/7] dt-bindings: i3c: Document core bindings
Hi Boris,

On Thu, Dec 14, 2017 at 4:16 PM, Boris Brezillon
<boris.brezillon@free-electrons.com> wrote:
> A new I3C subsystem has been added and a generic description has been
> created to represent the I3C bus and the devices connected on it.
>
> Document this generic representation.
>
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Thanks for your patch!

> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i3c/i3c.txt
> @@ -0,0 +1,128 @@
> +Generic device tree bindings for I3C busses
> +===========================================
> +
> +This document describes generic bindings that should be used to describe I3C
> +busses in a device tree.
> +
> +Required properties
> +-------------------
> +
> +- #address-cells - should be <1>. Read more about addresses below.
> +- #size-cells - should be <0>.
> +- compatible - name of I3C bus controller following generic names
> + recommended practice.
> +
> +For other required properties e.g. to describe register sets,
> +clocks, etc. check the binding documentation of the specific driver.
> +
> +Optional properties
> +-------------------
> +
> +These properties may not be supported by all I3C master drivers. Each I3C
> +master bindings should specify which of them are supported.
> +
> +- i3c-scl-frequency: frequency (in Hz) of the SCL signal used for I3C
> + transfers. When undefined the core set it to 12.5MHz.

sets

> +
> +- i2c-scl-frequency: frequency (in Hz) of the SCL signal used for I2C
> + transfers. When undefined, the core looks at LVR values

LVR (Legacy I2C Virtual Register)

> + of I2C devices described in the device tree to determine
> + the maximum I2C frequency.
> +
> +I2C devices
> +===========
> +
> +Each I2C device connected to the bus should be described in a subnode with
> +the following properties:

This colon looks a bit funny here, as below is a sentence, not a list.

> +
> +All properties described in Documentation/devicetree/bindings/i2c/i2c.txt are
> +valid here.

Perhaps rewrite as:

Each I2C device connected to the bus should be described in a subnode with
properties. All properties described in
Documentation/devicetree/bindings/i2c/i2c.txt are valid here, but several
new properties have been added.

> +
> +New required properties:
> +------------------------
> +- i3c-lvr: 32 bits integer property (only the lowest 8 bits are meaningful)
> + describing device capabilities as described in the I3C
> + specification.
> +
> + bit[31:8]: unused
> + bit[7:5]: I2C device index. Possible values
> + * 0: I2C device has a 50 ns spike filter
> + * 1: I2C device does not have a 50 ns spike filter but supports high
> + frequency on SCL
> + * 2: I2C device does not have a 50 ns spike filter and is not
> + tolerant to high frequencies
> + * 3-7: reserved
> +
> + bit[4]: tell whether the device operates in FM or FM+ mode
> + * 0: FM+ mode
> + * 1: FM mode

As this is the only reference to "FM", perhaps clarify the acronym, like you
do for DAA below.

> +
> + bit[3:0]: device type
> + * 0-15: reserved
> +
> +I3C devices
> +===========
> +
> +All I3C devices are supposed to support DAA (Dynamic Address Assignment), and
> +are thus discoverable. So, by default, I3C devices do not have to be described
> +in the device tree.
> +This being said, one might want to attach extra resources to these devices,
> +and those resources may have to be described in the device tree, which in turn
> +means we have to describe I3C devices.
> +
> +Another use case for describing an I3C device in the device tree is when this
> +I3C device has a static address and we want to assign it a specific dynamic
> +address before the DAA takes place (so that other devices on the bus can't
> +take this dynamic address).
> +
> +Required properties
> +-------------------
> +- i3c-pid: PID (Provisional ID). 64-bit property which is used to match a
> + device discovered during DAA with its device tree definition. The
> + PID is supposed to be unique on a given bus, which guarantees a 1:1
> + match. This property becomes optional if a reg property is defined,
> + meaning that the device has a static address.
> +
> +Optional properties
> +-------------------
> +- reg: static address. Only valid is the device has a static address.

if


--
Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2017-12-14 17:24    [W:0.248 / U:1.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site