lkml.org 
[lkml]   [2016]   [Jul]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/5] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac
Hi,

On Wed, Jul 20, 2016 at 10:03:18AM +0200, LABBE Corentin wrote:
> This patch adds documentation for Device-Tree bindings for the
> Allwinner sun8i-emac driver.
>
> Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
> ---
> .../bindings/net/allwinner,sun8i-emac.txt | 65 ++++++++++++++++++++++
> 1 file changed, 65 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
>
> diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> new file mode 100644
> index 0000000..4bf4e53
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> @@ -0,0 +1,65 @@
> +* Allwinner sun8i EMAC ethernet controller
> +
> +Required properties:
> +- compatible: "allwinner,sun8i-a83t-emac", "allwinner,sun8i-h3-emac",
> + or "allwinner,sun50i-a64-emac"
> +- reg: address and length of the register sets for the device.
> +- reg-names: should be "emac" and "syscon", matching the register sets

Blindly mapping a register of some other device on the SoC doesn't
look very reasonable.

> +- interrupts: interrupt for the device
> +- clocks: A phandle to the reference clock for this device
> +- clock-names: should be "ahb"
> +- resets: A phandle to the reset control for this device
> +- reset-names: should be "ahb"
> +- phy-mode: See ethernet.txt
> +- phy or phy-handle: See ethernet.txt
> +- #address-cells: shall be 1
> +- #size-cells: shall be 0
> +
> +"allwinner,sun8i-h3-emac" also requires:
> +- clocks: an extra phandle to the reference clock for the EPHY
> +- clock-names: an extra "ephy" entry matching the clocks property
> +- resets: an extra phandle to the reset control for the EPHY
> +- resets-names: an extra "ephy" entry matching the resets property

Shouldn't that be attached to the phy itself?

> +See ethernet.txt in the same directory for generic bindings for ethernet
> +controllers.
> +
> +The device node referenced by "phy" or "phy-handle" should be a child node
> +of this node. See phy.txt for the generic PHY bindings.
> +
> +Optional properties:
> +- phy-supply: phandle to a regulator if the PHY needs one
> +- phy-io-supply: phandle to a regulator if the PHY needs a another one for I/O.
> + This is sometimes found with RGMII PHYs, which use a second
> + regulator for the lower I/O voltage.
> +- allwinner,tx-delay: The setting of the TX clock delay chain
> +- allwinner,rx-delay: The setting of the RX clock delay chain

In which unit? What is the default value?

> +
> +The TX/RX clock delay chain settings are board specific.
> +
> +Optional properties for "allwinner,sun8i-h3-emac":
> +- allwinner,use-internal-phy: Use the H3 SoC's internal E(thernet) PHY

Can't that be derived from the presence of the phy property?

> +- allwinner,leds-active-low: EPHY LEDs are active low

That also seems PHY related. Overall, I feel like we really need a phy
node for the internal phy.

Maxime

--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2016-07-21 10:41    [W:0.184 / U:0.144 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site