lkml.org 
[lkml]   [2016]   [May]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 22/22] ARM: dts: exynos: Add RTC and I2C to Exynos5410
Date
Configure Exynos5410-specific properties of RTC, I2C and HSI2C nodes.
This still does not enable them on the board level though.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos5410.dtsi | 63 +++++++++++++++++++++++++++++++++++++++
1 file changed, 63 insertions(+)

diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
index 6146bf164248..a937d9bdad90 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/exynos5410.dtsi
@@ -149,6 +149,62 @@
};
};

+&i2c_0 {
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+};
+
+&i2c_1 {
+ clocks = <&clock CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+};
+
+&i2c_2 {
+ clocks = <&clock CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
+
+&i2c_3 {
+ clocks = <&clock CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+};
+
+&hsi2c_4 {
+ clocks = <&clock CLK_USI0>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_hs_bus>;
+};
+
+&hsi2c_5 {
+ clocks = <&clock CLK_USI1>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_hs_bus>;
+};
+
+&hsi2c_6 {
+ clocks = <&clock CLK_USI2>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_hs_bus>;
+};
+
+&hsi2c_7 {
+ clocks = <&clock CLK_USI3>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_hs_bus>;
+};
+
&mct {
clocks = <&fin_pll>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
@@ -159,6 +215,13 @@
clock-names = "timers";
};

+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
&serial_0 {
clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
clock-names = "uart", "clk_uart_baud0";
--
2.7.4
\
 
 \ /
  Last update: 2016-05-28 12:01    [W:0.157 / U:0.764 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site