lkml.org 
[lkml]   [2015]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 1/1] ARM: dts: sun7i: Enable axp209 driver on olinuxino lime2
On Fri, Sep 11, 2015 at 2:13 AM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> Hi Oliver,
>
> On Wed, Sep 09, 2015 at 03:26:44PM +0200, Olliver Schinagl wrote:
>> The Olimex OLinuXino Lime2 uses the same AXP209 as was recently
>> introduced this driver for its power regulation.
>>
>> Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
>> ---
>> arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 87 +++++++++----------------
>> 1 file changed, 31 insertions(+), 56 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> index d5c796c..dd90a1d 100644
>> --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> @@ -71,14 +71,6 @@
>> default-state = "on";
>> };
>> };
>> -
>> - reg_axp_ipsout: axp_ipsout {
>> - compatible = "regulator-fixed";
>> - regulator-name = "axp-ipsout";
>> - regulator-min-microvolt = <5000000>;
>> - regulator-max-microvolt = <5000000>;
>> - regulator-always-on;
>> - };
>
> Why are you removing that regulator?

This is really just a placeholder, rather than an actual regulator.

From the bindings:

- <input>-supply: a phandle to the regulator supply node. May be omitted if
inputs are unregulated, such as using the IPSOUT output
from the PMIC.


>> };
>>
>> &ahci {
>> @@ -86,6 +78,10 @@
>> status = "okay";
>> };
>>
>> +&cpu0 {
>> + cpu-supply = <&reg_dcdc2>;
>> +};
>> +
>> &ehci0 {
>> status = "okay";
>> };
>> @@ -112,57 +108,9 @@
>> status = "okay";
>>
>> axp209: pmic@34 {
>> - compatible = "x-powers,axp209";
>> reg = <0x34>;
>> interrupt-parent = <&nmi_intc>;
>> interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> -
>> - interrupt-controller;
>> - #interrupt-cells = <1>;
>> -
>> - acin-supply = <&reg_axp_ipsout>;
>> - vin2-supply = <&reg_axp_ipsout>;
>> - vin3-supply = <&reg_axp_ipsout>;
>> - ldo24in-supply = <&reg_axp_ipsout>;
>> - ldo3in-supply = <&reg_axp_ipsout>;
>
> And these supplies?
>
>> - regulators {
>> - vdd_rtc: ldo1 {
>> - regulator-min-microvolt = <1300000>;
>> - regulator-max-microvolt = <1300000>;
>> - regulator-always-on;
>> - };
>> -
>> - avcc: ldo2 {
>> - regulator-min-microvolt = <1800000>;
>> - regulator-max-microvolt = <3300000>;
>> - regulator-always-on;
>> - };
>> -
>> - vcc_csi0: ldo3 {
>> - regulator-min-microvolt = <700000>;
>> - regulator-max-microvolt = <3500000>;
>> - regulator-always-on;
>> - };
>> -
>> - vcc_csi1: ldo4 {
>> - regulator-min-microvolt = <1250000>;
>> - regulator-max-microvolt = <3300000>;
>> - regulator-always-on;
>> - };
>> -
>> - vdd_cpu: dcdc2 {
>> - regulator-min-microvolt = <700000>;
>> - regulator-max-microvolt = <2275000>;
>> - regulator-always-on;
>> - };
>> -
>> - vdd_int: dcdc3 {
>> - regulator-min-microvolt = <700000>;
>> - regulator-max-microvolt = <3500000>;
>> - regulator-always-on;
>> - };
>> - };
>> };
>> };
>>
>> @@ -243,6 +191,33 @@
>> status = "okay";
>> };
>>
>> +#include "axp209.dtsi"
>> +
>> +&reg_dcdc2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1450000>;
>
> This is outside of the operating voltages of the CPU.
>
>> + regulator-name = "vdd-cpu";
>> +};
>> +
>> +&reg_dcdc3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-int-dll";
>> +};
>> +
>> +&reg_ldo1 {
>> + regulator-name = "vdd-rtc";
>> +};
>> +
>> +&reg_ldo2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-name = "avcc";
>
> You're changing the boundaries, why?

The old boundaries seem to be from a very old dts, where we were
listing the regulators' supported voltage range, instead of what
the SoC could take.

Olliver you should explain all this in the commit log, probably
starting with something like "update the dts to use axp209.dtsi
, comply with axp20x bindings, and set proper voltage ranges for
the regulators".

>> +};
>> +
>> &reg_usb0_vbus {
>> pinctrl-0 = <&usb0_vbus_pin_lime2>;
>> gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
>> --
>> 2.1.4
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>


\
 
 \ /
  Last update: 2015-09-11 05:21    [W:0.063 / U:2.960 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site