lkml.org 
[lkml]   [2015]   [Jul]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 1/2] iio: adc: vf610: Determine sampling frequencies by using minimum sample time
On 14/07/15 14:53, Sanchayan Maity wrote:
> The driver currently does not take into account the minimum sample time
> as per the Figure 6-8 Chapter 9.1.1 12-bit ADC electrical characteristics.
> We set a static amount of cycles instead of considering the sample time
> as a given value, which depends on hardware characteristics.
>
> Determine sampling frequencies by first reading the device tree property
> node and then calculating the required Long Sample Time Adder (LSTAdder)
> value, based on the ADC clock frequency and sample time value obtained
> from the device tree. This LSTAdder value is then used for calculating
> the sampling frequencies possible.
>
> In case the sample time property is not specified through the device
> tree, a safe default value of 1000ns is assumed.
>
> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Applied with the Acks from Stefan and Fugang as the patch has changed very little
from the previous version.

Applied to the togreg branch of iio.git - initially pushed out as testing for
the autobuilders to play with it.

Thanks,

Jonathan
> ---
> .../devicetree/bindings/iio/adc/vf610-adc.txt | 5 ++
> drivers/iio/adc/vf610_adc.c | 79 ++++++++++++++++++++--
> 2 files changed, 80 insertions(+), 4 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
> index 3eb40e2..1aad051 100644
> --- a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
> +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
> @@ -17,6 +17,11 @@ Recommended properties:
> - Frequency in normal mode (ADLPC=0, ADHSC=0)
> - Frequency in high-speed mode (ADLPC=0, ADHSC=1)
> - Frequency in low-power mode (ADLPC=1, ADHSC=0)
> +- min-sample-time: Minimum sampling time in nanoseconds. This value has
> + to be chosen according to the conversion mode and the connected analog
> + source resistance (R_as) and capacitance (C_as). Refer the datasheet's
> + operating requirements. A safe default across a wide range of R_as and
> + C_as as well as conversion modes is 1000ns.
>
> Example:
> adc0: adc@4003b000 {
> diff --git a/drivers/iio/adc/vf610_adc.c b/drivers/iio/adc/vf610_adc.c
> index 480f335..23b8fb9 100644
> --- a/drivers/iio/adc/vf610_adc.c
> +++ b/drivers/iio/adc/vf610_adc.c
> @@ -68,6 +68,9 @@
> #define VF610_ADC_CLK_DIV8 0x60
> #define VF610_ADC_CLK_MASK 0x60
> #define VF610_ADC_ADLSMP_LONG 0x10
> +#define VF610_ADC_ADSTS_SHORT 0x100
> +#define VF610_ADC_ADSTS_NORMAL 0x200
> +#define VF610_ADC_ADSTS_LONG 0x300
> #define VF610_ADC_ADSTS_MASK 0x300
> #define VF610_ADC_ADLPC_EN 0x80
> #define VF610_ADC_ADHSC_EN 0x400
> @@ -98,6 +101,8 @@
> #define VF610_ADC_CALF 0x2
> #define VF610_ADC_TIMEOUT msecs_to_jiffies(100)
>
> +#define DEFAULT_SAMPLE_TIME 1000
> +
> enum clk_sel {
> VF610_ADCIOC_BUSCLK_SET,
> VF610_ADCIOC_ALTCLK_SET,
> @@ -124,6 +129,17 @@ enum conversion_mode_sel {
> VF610_ADC_CONV_LOW_POWER,
> };
>
> +enum lst_adder_sel {
> + VF610_ADCK_CYCLES_3,
> + VF610_ADCK_CYCLES_5,
> + VF610_ADCK_CYCLES_7,
> + VF610_ADCK_CYCLES_9,
> + VF610_ADCK_CYCLES_13,
> + VF610_ADCK_CYCLES_17,
> + VF610_ADCK_CYCLES_21,
> + VF610_ADCK_CYCLES_25,
> +};
> +
> struct vf610_adc_feature {
> enum clk_sel clk_sel;
> enum vol_ref vol_ref;
> @@ -132,6 +148,8 @@ struct vf610_adc_feature {
> int clk_div;
> int sample_rate;
> int res_mode;
> + u32 lst_adder_index;
> + u32 default_sample_time;
>
> bool calibration;
> bool ovwren;
> @@ -155,11 +173,13 @@ struct vf610_adc {
> };
>
> static const u32 vf610_hw_avgs[] = { 1, 4, 8, 16, 32 };
> +static const u32 vf610_lst_adder[] = { 3, 5, 7, 9, 13, 17, 21, 25 };
>
> static inline void vf610_adc_calculate_rates(struct vf610_adc *info)
> {
> struct vf610_adc_feature *adc_feature = &info->adc_feature;
> unsigned long adck_rate, ipg_rate = clk_get_rate(info->clk);
> + u32 adck_period, lst_addr_min;
> int divisor, i;
>
> adck_rate = info->max_adck_rate[adc_feature->conv_mode];
> @@ -174,6 +194,19 @@ static inline void vf610_adc_calculate_rates(struct vf610_adc *info)
> }
>
> /*
> + * Determine the long sample time adder value to be used based
> + * on the default minimum sample time provided.
> + */
> + adck_period = NSEC_PER_SEC / adck_rate;
> + lst_addr_min = adc_feature->default_sample_time / adck_period;
> + for (i = 0; i < ARRAY_SIZE(vf610_lst_adder); i++) {
> + if (vf610_lst_adder[i] > lst_addr_min) {
> + adc_feature->lst_adder_index = i;
> + break;
> + }
> + }
> +
> + /*
> * Calculate ADC sample frequencies
> * Sample time unit is ADCK cycles. ADCK clk source is ipg clock,
> * which is the same as bus clock.
> @@ -182,12 +215,13 @@ static inline void vf610_adc_calculate_rates(struct vf610_adc *info)
> * SFCAdder: fixed to 6 ADCK cycles
> * AverageNum: 1, 4, 8, 16, 32 samples for hardware average.
> * BCT (Base Conversion Time): fixed to 25 ADCK cycles for 12 bit mode
> - * LSTAdder(Long Sample Time): fixed to 3 ADCK cycles
> + * LSTAdder(Long Sample Time): 3, 5, 7, 9, 13, 17, 21, 25 ADCK cycles
> */
> adck_rate = ipg_rate / info->adc_feature.clk_div;
> for (i = 0; i < ARRAY_SIZE(vf610_hw_avgs); i++)
> info->sample_freq_avail[i] =
> - adck_rate / (6 + vf610_hw_avgs[i] * (25 + 3));
> + adck_rate / (6 + vf610_hw_avgs[i] *
> + (25 + vf610_lst_adder[adc_feature->lst_adder_index]));
> }
>
> static inline void vf610_adc_cfg_init(struct vf610_adc *info)
> @@ -347,8 +381,40 @@ static void vf610_adc_sample_set(struct vf610_adc *info)
> break;
> }
>
> - /* Use the short sample mode */
> - cfg_data &= ~(VF610_ADC_ADLSMP_LONG | VF610_ADC_ADSTS_MASK);
> + /*
> + * Set ADLSMP and ADSTS based on the Long Sample Time Adder value
> + * determined.
> + */
> + switch (adc_feature->lst_adder_index) {
> + case VF610_ADCK_CYCLES_3:
> + break;
> + case VF610_ADCK_CYCLES_5:
> + cfg_data |= VF610_ADC_ADSTS_SHORT;
> + break;
> + case VF610_ADCK_CYCLES_7:
> + cfg_data |= VF610_ADC_ADSTS_NORMAL;
> + break;
> + case VF610_ADCK_CYCLES_9:
> + cfg_data |= VF610_ADC_ADSTS_LONG;
> + break;
> + case VF610_ADCK_CYCLES_13:
> + cfg_data |= VF610_ADC_ADLSMP_LONG;
> + break;
> + case VF610_ADCK_CYCLES_17:
> + cfg_data |= VF610_ADC_ADLSMP_LONG;
> + cfg_data |= VF610_ADC_ADSTS_SHORT;
> + break;
> + case VF610_ADCK_CYCLES_21:
> + cfg_data |= VF610_ADC_ADLSMP_LONG;
> + cfg_data |= VF610_ADC_ADSTS_NORMAL;
> + break;
> + case VF610_ADCK_CYCLES_25:
> + cfg_data |= VF610_ADC_ADLSMP_LONG;
> + cfg_data |= VF610_ADC_ADSTS_NORMAL;
> + break;
> + default:
> + dev_err(info->dev, "error in sample time select\n");
> + }
>
> /* update hardware average selection */
> cfg_data &= ~VF610_ADC_AVGS_MASK;
> @@ -713,6 +779,11 @@ static int vf610_adc_probe(struct platform_device *pdev)
> of_property_read_u32_array(pdev->dev.of_node, "fsl,adck-max-frequency",
> info->max_adck_rate, 3);
>
> + ret = of_property_read_u32(pdev->dev.of_node, "min-sample-time",
> + &info->adc_feature.default_sample_time);
> + if (ret)
> + info->adc_feature.default_sample_time = DEFAULT_SAMPLE_TIME;
> +
> platform_set_drvdata(pdev, indio_dev);
>
> init_completion(&info->completion);
>



\
 
 \ /
  Last update: 2015-07-19 15:01    [W:0.083 / U:0.800 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site