lkml.org 
[lkml]   [2015]   [Jul]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] ALSA: hda/realtek: Enable HP amp and mute LED on HP Folio 9480m
On Wed, 15 Jul 2015 04:37:44 +0200,
Keith Packard wrote:
>
> Takashi Iwai <tiwai@suse.de> writes:
>
> > Thanks for the patch. But this looks suboptimal, unfortunately, since
> > it keeps the amp always on, and more badly, it would block the power
> > save of the widget root node.
>
> Thanks very much for your feedback; I wasn't sure precisely how this
> code worked and tried to make a change that was as close as I could
> manage to existing examples.
>
> > Can just using gpio_mute_led_mask=0x18 and gpio_led=0 (also drop
> > AC_VERB_SET_GPIO_DATA in gpio_init[]) work instead? If GPIO4 is the
> > the amp, we can associate it with the master mute control together
> > with the mute LED. The only concern would be the possible click
> > noise, but it doesn't happen on most machines.
>
> It's not quite that simple; the GPIO4 value is inverted from the mute
> LED value (the amp is powered up when GPIO4 is set).

Ah, right, there was already a fixup for GPIO4 low, and yours is for
GPIO4 high.

> What I've done is to make the amp powered only when a headphone is
> plugged in, and then removed the code which was disabling power saving,
> which lets everything (including the amp) get turned back off when the
> device goes idle.
>
> Here's a second version of the patch.

Thanks! The new patch looks good, but I think we don't have to use
the headset code, as your case looks more like a headphone, not a
combo headset that needs the special handling. If so, the change can
be reduced something like below. Could you check whether this is
enough?


Takashi

--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -3430,6 +3430,37 @@ static void alc280_fixup_hp_gpio4(struct hda_codec *codec,
}
}

+static void alc280_hp_gpio4_hp_automue(struct hda_codec *codec,
+ struct hda_jack_callback *jack)
+{
+ snd_hda_gen_hp_automute(codec, jack);
+ /* mute_led_polarity is set to 0, so we pass inverted value here */
+ alc_update_gpio_led(codec, 0x10, !spec->gen.hp_jack_present);
+}
+
+/* GPIO3 = mute LED, GPIO4 high = enable headphone amp */
+static void alc280_fixup_hp_gpio4_hp_amp(struct hda_codec *codec,
+ const struct hda_fixup *fix,
+ int action)
+{
+ struct alc_spec *spec = codec->spec;
+ static const struct hda_verb gpio_init[] = {
+ { 0x01, AC_VERB_SET_GPIO_MASK, 0x18 },
+ { 0x01, AC_VERB_SET_GPIO_DIRECTION, 0x18 },
+ {}
+ };
+
+ if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+ spec->gen.vmaster_mute.hook = alc_fixup_gpio_mute_hook;
+ spec->gen.hp_automute_hook = alc280_hp_gpio4_hp_automue;
+ spec->gpio_led = 0;
+ spec->mute_led_polarity = 0;
+ spec->gpio_mute_led_mask = 0x08;
+ snd_hda_add_verbs(codec, gpio_init);
+ codec->power_filter = led_power_filter;
+ }
+}
+


\
 
 \ /
  Last update: 2015-07-15 10:41    [W:0.093 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site