lkml.org 
[lkml]   [2015]   [Jul]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v1 3/7] mtd: fsl-quadspi: Support both 24- and 32-bit addressed commands.
Date
Hello Cory,

On Wednesday 08 July 2015 16:21:17, Cory Tusar wrote:
> The current fsl-quadspi implementation assumes that all connected
> devices are of the same size and type. This commit adds lookup table
> entries for both 24- and 32-bit addressed variants of the read, sector
> erase, and page program operations as a precursor to later changes which
> generalize the flash layout parsing logic and allow for non-contiguous
> and non-homogeneous chip combinations.
>
> Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
>
> [...]
> /* Get the SEQID for the command */
> -static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
> +static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd, u8 addr_width)
> {
> switch (cmd) {
> case SPINOR_OP_READ_1_1_4:
> - return SEQID_QUAD_READ;
> + if (addr_width == 3)
> + return SEQID_QUAD_READ_24;
> + if (addr_width == 4)
> + return SEQID_QUAD_READ_32;
> + dev_err(q->dev, "Unsupported addr_width (%d) for cmd 0x%.2x\n",
> + addr_width, cmd);
> + break;

Does this actually work? What if q->nor[0].read_opcode is SPINOR_OP_READ4_1_1_4 (set in spi-nor.c for flashes using 4 byte address commands)?

> case SPINOR_OP_WREN:
> return SEQID_WREN;
> case SPINOR_OP_WRDI:
> @@ -403,11 +394,23 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
> case SPINOR_OP_RDSR:
> return SEQID_RDSR;
> case SPINOR_OP_SE:
> - return SEQID_SE;
> + if (addr_width == 3)
> + return SEQID_SE_24;
> + if (addr_width == 4)
> + return SEQID_SE_32;
> + dev_err(q->dev, "Unsupported addr_width (%d) for cmd 0x%.2x\n",
> + addr_width, cmd);
> + break;

Same as for read command.

> case SPINOR_OP_CHIP_ERASE:
> return SEQID_CHIP_ERASE;
> case SPINOR_OP_PP:
> - return SEQID_PP;
> + if (addr_width == 3)
> + return SEQID_PP_24;
> + if (addr_width == 4)
> + return SEQID_PP_32;
> + dev_err(q->dev, "Unsupported addr_width (%d) for cmd 0x%.2x\n",
> + addr_width, cmd);
> + break;

See above too.

> case SPINOR_OP_RDID:
> return SEQID_RDID;
> case SPINOR_OP_WRSR:
> @@ -456,7 +459,7 @@ fsl_qspi_runcmd(struct fsl_qspi *q, u8 cmd, unsigned int addr, int len)
> } while (1);
>
> /* trigger the LUT now */
> - seqid = fsl_qspi_get_seqid(q, cmd);
> + seqid = fsl_qspi_get_seqid(q, cmd, q->nor[0].addr_width);
> writel((seqid << QUADSPI_IPCR_SEQID_SHIFT) | len, base + QUADSPI_IPCR);
>
> /* Wait for the interrupt. */
> @@ -601,9 +604,10 @@ static void fsl_qspi_init_abh_read(struct fsl_qspi *q)
> writel(0, base + QUADSPI_BUF2IND);
>
> /* Set the default lut sequence for AHB Read. */
> - seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode);
> + seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode,
> + q->nor[0].addr_width);
> writel(seqid << QUADSPI_BFGENCR_SEQID_SHIFT,

Those changes can then be skipped you explicitly do switch/case for 4 byte address commands.

Best reagrds,
Alexander
--
Dipl.-Inf. Alexander Stein

SYS TEC electronic GmbH
Am Windrad 2
08468 Heinsdorfergrund
Tel.: 03765 38600-1156
Fax: 03765 38600-4100
Email: alexander.stein@systec-electronic.com
Website: www.systec-electronic.com

Managing Director: Dipl.-Phys. Siegmar Schmidt
Commercial registry: Amtsgericht Chemnitz, HRB 28082



\
 
 \ /
  Last update: 2015-07-14 16:21    [W:0.074 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site