lkml.org 
[lkml]   [2015]   [Jun]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/3] net/phy: micrel: Center FLP timing at 16ms
Date
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.

From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.

The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.

Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
---
drivers/net/phy/micrel.c | 23 ++++++++++++++++++++++-
1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index f23765e..499185e 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -366,6 +366,10 @@ static int ksz9021_config_init(struct phy_device *phydev)
#define KSZ9031_PS_TO_REG 60

/* Extended registers */
+/* MMD Address 0x0 */
+#define MII_KSZ9031RN_FLP_BURST_TX_LO 3
+#define MII_KSZ9031RN_FLP_BURST_TX_HI 4
+
/* MMD Address 0x2 */
#define MII_KSZ9031RN_CONTROL_PAD_SKEW 4
#define MII_KSZ9031RN_RX_DATA_PAD_SKEW 5
@@ -427,6 +431,22 @@ static int ksz9031_of_load_skew_values(struct phy_device *phydev,
return ksz9031_extended_write(phydev, OP_DATA, 2, reg, newval);
}

+static int ksz9031_center_flp_timing(struct phy_device *phydev)
+{
+ int result;
+
+ /* Center KSZ9031RNX FLP timing at 16ms. */
+ result = ksz9031_extended_write(phydev, OP_DATA, 0,
+ MII_KSZ9031RN_FLP_BURST_TX_HI, 0x0006);
+ result = ksz9031_extended_write(phydev, OP_DATA, 0,
+ MII_KSZ9031RN_FLP_BURST_TX_LO, 0x1A80);
+
+ if (result)
+ return result;
+
+ return genphy_restart_aneg(phydev);
+}
+
static int ksz9031_config_init(struct phy_device *phydev)
{
const struct device *dev = &phydev->dev;
@@ -462,7 +482,8 @@ static int ksz9031_config_init(struct phy_device *phydev)
MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
tx_data_skews, 4);
}
- return 0;
+
+ return ksz9031_center_flp_timing(phydev);
}

#define KSZ8873MLL_GLOBAL_CONTROL_4 0x06
--
2.1.4


\
 
 \ /
  Last update: 2015-06-06 01:21    [W:0.106 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site