lkml.org 
[lkml]   [2015]   [Jun]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] i2c: mv64xxx: remove unreachable signal case handling
On Thu, Jun 11, 2015 at 05:27:33PM +0200, Nicholas Mc Guire wrote:
> 'commit d295a86eab20 ("i2c: mv64xxx: work around signals causing I2C
> transactions to be aborted")' removed the wait_event_interruptible_timeout
> to prevent half/mixed i2c messages from being sent/received but forgot to
> drop the signal received cases in the return handling. This just removes
> this dead code and simplifies the error message as "time_left" only can be
> 0 here and thus it conveys no additional information.
>
> Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
> ---
>
> Patch was compile tested with multi_v7_defconfig
> (implies CONFIG_I2C_MV64XXX=y)
>
> Patch is against 4.1-rc7 (localversion-next is -next-20150611)

Hmm, IMO this patch is too intrusive to be applied without actual
testing.

>
> drivers/i2c/busses/i2c-mv64xxx.c | 15 +++------------
> 1 file changed, 3 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c
> index 30059c1..a4f8ece 100644
> --- a/drivers/i2c/busses/i2c-mv64xxx.c
> +++ b/drivers/i2c/busses/i2c-mv64xxx.c
> @@ -534,7 +534,6 @@ mv64xxx_i2c_wait_for_completion(struct mv64xxx_i2c_data *drv_data)
> {
> long time_left;
> unsigned long flags;
> - char abort = 0;
>
> time_left = wait_event_timeout(drv_data->waitq,
> !drv_data->block, drv_data->adapter.timeout);
> @@ -542,25 +541,17 @@ mv64xxx_i2c_wait_for_completion(struct mv64xxx_i2c_data *drv_data)
> spin_lock_irqsave(&drv_data->lock, flags);
> if (!time_left) { /* Timed out */
> drv_data->rc = -ETIMEDOUT;
> - abort = 1;
> - } else if (time_left < 0) { /* Interrupted/Error */
> - drv_data->rc = time_left; /* errno value */
> - abort = 1;
> - }
> -
> - if (abort && drv_data->block) {
> drv_data->aborting = 1;
> spin_unlock_irqrestore(&drv_data->lock, flags);
>
> time_left = wait_event_timeout(drv_data->waitq,
> !drv_data->block, drv_data->adapter.timeout);
>
> - if ((time_left <= 0) && drv_data->block) {

I am especially unsure about the drv_data->block removal. Did you double
check if we can do this?

> + if (time_left == 0) {
> drv_data->state = MV64XXX_I2C_STATE_IDLE;
> dev_err(&drv_data->adapter.dev,
> - "mv64xxx: I2C bus locked, block: %d, "
> - "time_left: %d\n", drv_data->block,
> - (int)time_left);
> + "mv64xxx: I2C bus locked, block: %d\n",
> + drv_data->block);

And if so, shouldn't that also be always 1 in the output here?

> mv64xxx_i2c_hw_init(drv_data);
> }
> } else

Maybe (not sure) it also helps to split the patch into everything
dealing with time_left as patch 1) and simplifying by drv_data->block
removal as patch2?

Thanks,

Wolfram

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2015-06-17 15:21    [W:0.053 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site