lkml.org 
[lkml]   [2015]   [Mar]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/6] ARM: DT: STi: STiH407: Add dwc3 usb3 DT node.
Hi Peter,

On 02/25/2015 02:36 PM, Peter Griffin wrote:
> Now that both usb2 and usb3 phy drivers, and also the ST dwc3 glue code
> are all present upstream, we can add the dwc3 DT node and have a working
> usb3 controller on stih407-b2120 and stih410-b2020.
>
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
> arch/arm/boot/dts/stih407-family.dtsi | 26 ++++++++++++++++++++++++++
> 1 file changed, 26 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
> index 186412d..18ff5a5 100644
> --- a/arch/arm/boot/dts/stih407-family.dtsi
> +++ b/arch/arm/boot/dts/stih407-family.dtsi
> @@ -7,6 +7,7 @@
> * publishhed by the Free Software Foundation.
> */
> #include "stih407-pinctrl.dtsi"
> +#include <dt-bindings/phy/phy.h>
> #include <dt-bindings/reset-controller/stih407-resets.h>
> / {
> #address-cells = <1>;
> @@ -336,5 +337,30 @@
> resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
> };
> };
> +
> + st_dwc3: dwc3@8f94000 {
> + compatible = "st,stih407-dwc3";
> + reg = <0x08f94000 0x1000>, <0x110 0x4>;
> + reg-names = "reg-glue", "syscfg-reg";
> + st,syscfg = <&syscfg_core>;
> + resets = <&powerdown STIH407_USB3_POWERDOWN>,
> + <&softreset STIH407_MIPHY2_SOFTRESET>;
> + reset-names = "powerdown",
> + "softreset";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb3>;
> + ranges;
> +
> + dwc3: dwc3@9900000 {
> + compatible = "snps,dwc3";
> + reg = <0x09900000 0x100000>;
> + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
> + dr_mode = "host";
> + phy-names = "usb2-phy", "usb3-phy";
> + phys = <&usb2_picophy0>, <&phy_port2 PHY_TYPE_USB3>;
> + };
> + };
> };
> };

The USB3 port should only be enabled in the board files, not the soc one.
We can have a board without USB3 port, so it should be disbaled by default.

Other than that, you can enable it also on stih418-b2199, just tested
and it is working.

Thanks,
Maxime


\
 
 \ /
  Last update: 2015-03-04 15:41    [W:1.751 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site