Messages in this thread | | | Date | Mon, 23 Feb 2015 15:38:16 +0100 | From | Nicolas Ferre <> | Subject | Re: [PATCH] net: macb: Add big endian CPU support |
| |
Le 20/02/2015 12:45, Arun Chandran a écrit : > On Thu, Feb 19, 2015 at 5:52 PM, Michal Simek <monstr@monstr.eu> wrote: >> >> On 02/18/2015 12:29 PM, Arun Chandran wrote: >>> This patch converts all __raw_readl and __raw_writel function calls >>> to their corresponding readl_relaxed and writel_relaxed variants. >>> >>> It also tells the driver to set ahb_endian_swp_mgmt_en bit in dma_cfg >>> when the CPU is configured in big endian mode. >>> >>> Signed-off-by: Arun Chandran <achandran@mvista.com> >>> --- >>> This patch is tested on xilinx ZC702 evaluation board with >>> CONFIG_CPU_BIG_ENDIAN=y and booting NFS rootfs >>> --- >>> --- >>> drivers/net/ethernet/cadence/macb.c | 18 ++++++++++++------ >>> drivers/net/ethernet/cadence/macb.h | 15 ++++++++------- >>> 2 files changed, 20 insertions(+), 13 deletions(-) >>> >>> diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c >>> index ad76b8e..05fb36d 100644 >>> --- a/drivers/net/ethernet/cadence/macb.c >>> +++ b/drivers/net/ethernet/cadence/macb.c >>> @@ -449,7 +449,7 @@ static void macb_update_stats(struct macb *bp) >>> WARN_ON((unsigned long)(end - p - 1) != (MACB_TPF - MACB_PFR) / 4); >>> >>> for(; p < end; p++, reg++) >>> - *p += __raw_readl(reg); >>> + *p += readl_relaxed(reg); >>> } >>> >>> static int macb_halt_tx(struct macb *bp) >>> @@ -1585,7 +1585,11 @@ static void macb_configure_dma(struct macb *bp) >>> if (bp->dma_burst_length) >>> dmacfg = GEM_BFINS(FBLDO, bp->dma_burst_length, dmacfg); >>> dmacfg |= GEM_BIT(TXPBMS) | GEM_BF(RXBMS, -1L); >>> - dmacfg &= ~GEM_BIT(ENDIA); >>> + dmacfg &= ~GEM_BIT(ENDIA_PKT); >>> + /* Tell the chip to byteswap descriptors on big-endian hosts */ >>> +#ifdef __BIG_ENDIAN >>> + dmacfg |= GEM_BIT(ENDIA_DESC); >>> +#endif >> >> I don't think this is the best way what you should do. >> Instead of having this ifdef here you should find out any reg and detect if the IP >> is in big endian or little endian mode. I have done it for some xilinx IPs which >> can run on big or little endian system. >> In general find reg which some field which has some meaning - write there 1 >> and read expected value and based on that decide if you are on big or little endian system. > > Hi Michal, > > I was not able to find any such registers for GEM in the TRM > http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf > > I tried writing to dma_cfg (0x00000010) and reading from design_cfg5 > (0x00000290) > Its not reflecting anything(design_cfg5 always reads same value); It > is not helping.
0kay, here you mean that the design_cfg5 (@0x290) and its bit 16:15 "gem_endian_swap_def" doesn't change depending on the big/little endian configuration you use?
I was also thinking about this configuration bit... too bad...
Bye,
> The only way (I don't think its not right way either) I can think of > eliminating that > #ifdef __BIG_ENDIAN is reading some register in ARM cpu to identify its > current endianness and write dma_cfg accordingly. > > --Arun > >
-- Nicolas Ferre
| |