lkml.org 
[lkml]   [2015]   [Feb]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/5] ARM: dts: sun9i: Enable USB support on A80 Optimus board
Date
On the Optimus board, all three USB hosts can be used.
HCI0 and HCI2 are available through the USB connector.
HCI1 is available with HSIC through 2 pins on the GPIO
expansion header.

This patch also adds a regulator for HCI2/USB3's VBUS.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun9i-a80-optimus.dts | 65 +++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)

diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index c4de9cb9a5f6..af6ac07ca5f6 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -81,6 +81,29 @@
gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>;
};
};
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb3_vbus_pin_optimus>;
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
};

&i2c3 {
@@ -94,6 +117,14 @@
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};

+&ohci0 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
&pio {
led_pins_optimus: led-pins@0 {
allwinner,pins = "PH0", "PH1";
@@ -108,6 +139,20 @@
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
+
+ usb1_vbus_pin_optimus: usb1_vbus_pin@1 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb3_vbus_pin_optimus: usb3_vbus_pin@1 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};

&mmc0 {
@@ -129,6 +174,12 @@
status = "okay";
};

+&reg_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_optimus>;
+ gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
@@ -145,3 +196,17 @@
/* Enable internal pull-up */
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
+
+&usbphy1 {
+ vbus-supply = <&reg_usb1_vbus>;
+ status = "okay";
+};
+
+&usbphy2 {
+ status = "okay";
+};
+
+&usbphy3 {
+ vbus-supply = <&reg_usb3_vbus>;
+ status = "okay";
+};
--
2.1.4


\
 
 \ /
  Last update: 2015-02-03 00:01    [W:0.051 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site