Messages in this thread | | | Date | Mon, 30 Nov 2015 21:07:42 +0800 | From | Jisheng Zhang <> | Subject | Re: [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality |
| |
On Sat, 28 Nov 2015 12:20:01 +0100 Sebastian Hesselbarth wrote:
> On 26.11.2015 14:13, Jisheng Zhang wrote: > > The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we > > have gpios for card detection, write-protect, vqmmc and vmmc. > > > > This patch adds pinmux for this sdcard interface, then adds regulators > > for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties. > > > > Signed-off-by: Jisheng Zhang <jszhang@marvell.com> > > --- > > arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 43 ++++++++++++++++++++++++++++-- > > 1 file changed, 41 insertions(+), 2 deletions(-) > > > > diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts > > index cdcf89b..1fdc1d7 100644 > > --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts > > +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts > > @@ -84,12 +84,51 @@ > > gpio = <&portb 12 GPIO_ACTIVE_HIGH>; > > enable-active-high; > > }; > > + > > + reg_sdio1_vmmc: regulator@3 { > > + compatible = "regulator-fixed"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "sdio1_vmmc"; > > + enable-active-high; > > + regulator-boot-on; > > + gpio = <&portb 21 GPIO_ACTIVE_HIGH>; > > + }; > > + > > + reg_sdio1_vqmmc: regulator@4 { > > + compatible = "regulator-gpio"; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "sdio1_vqmmc"; > > + regulator-type = "voltage"; > > + enable-active-high; > > + gpios = <&portb 16 GPIO_ACTIVE_HIGH>; > > + states = <3300000 0x1 > > + 1800000 0x0>; > > + }; > > + }; > > +}; > > + > > +&soc_pinctrl { > > + sd1gpio_pmux: sd1pwr-pmux { > > + groups = "G23", "G32"; > > + function = "gpio"; > > + }; > > + > > + sd1_pmux: sd1-pmux { > > + groups = "G31"; > > + function = "sd1"; > > Jisheng, > > while having the sd1gpio_pmux in the board file, I think the > sd1_pmux is best kept in the SoC.dtsi.
Indeed, there's no other usage with sd1's pinmux. will do in v2
> > > }; > > }; > > > > &sdhci1 { > > - broken-cd; > > - sdhci,wp-inverted; > > + vmmc-supply = <®_sdio1_vmmc>; > > + vqmmc-supply = <®_sdio1_vqmmc>; > > + cd-inverted; > > + cd-gpios = <&portc 30 GPIO_ACTIVE_HIGH>; > > How about removing cd-inverted and make cd-gpio GPIO_ACTIVE_LOW > instead?
Good idea! Will do in v2.
Thanks for your review, Jisheng
| |