lkml.org 
[lkml]   [2015]   [Nov]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH RESEND 01/16] Documentation: dt-bindings: mfd: add TI LMU device binding information
From
Date
Thanks for all your comments. I'll create the 2nd patch-set in few weeks.

Best regards,
Milo

On 11/11/2015 6:49 PM, Lee Jones wrote:
> On Mon, 02 Nov 2015, Milo Kim wrote:
>
>> This patch describes overall binding for TI LMU MFD devices.
>>
>> Cc: devicetree@vger.kernel.org
>> Cc: Lee Jones <lee.jones@linaro.org>
>> Cc: linux-kernel@vger.kernel.org
>> Signed-off-by: Milo Kim <milo.kim@ti.com>
>> ---
>> Documentation/devicetree/bindings/mfd/ti-lmu.txt | 282 +++++++++++++++++++++++
>> 1 file changed, 282 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/ti-lmu.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
>> new file mode 100644
>> index 0000000..7ccf07e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
>> @@ -0,0 +1,282 @@
>> +TI LMU(Lighting Management Unit) device tree bindings
>
> ' ' here -^
>
>> +TI LMU driver supports lighting devices belows.
>
> s/belows./below:/
>
>> + Name Child nodes
>> + ------ -------------------------
>> + LM3532 Backlight
>> + LM3631 Backlight and regulator
>> + LM3632 Backlight and regulator
>> + LM3633 Backlight, LED and HWMON
>> + LM3695 Backlight
>> + LM3697 Backlight and HWMON
>> +
>> +Required properties:
>> + - compatible: Should be one of lists below.
>
> s/ lists below./:/
>
>> + "ti,lm3532"
>> + "ti,lm3631"
>> + "ti,lm3632"
>> + "ti,lm3633"
>> + "ti,lm3695"
>> + "ti,lm3697"
>> + - reg: I2C slave address.
>> + 0x11 is LM3632
>> + 0x29 is LM3631
>> + 0x36 is LM3633, LM3697
>> + 0x38 is LM3532
>> + 0x63 is LM3695
>
> s/is/for/
>
>> +Optional properties:
>> + - enable-gpios: A GPIO specifier for hardware enable pin.
>> +
>> +Required node:
>> + - backlight: All LMU devices have backlight child nodes.
>> + For the properties, please refer to [1].
>> +
>> +Optional nodes:
>> + - hwmon: Hardware fault monitoring driver for LM3633 and LM3697.
>> + For the property, please refer to [2].
>> + - leds: LED properties for LM3633. Please refer to [3].
>> + - regulators: Regulator properties for LM3631 and LM3632.
>> + Please refer to [4].
>> +
>> +[1] Documentation/devicetree/bindings/video/backlight/ti-lmu-backlight.txt
>> +[2] Documentation/devicetree/bindings/hwm/ti-lmu-hwmon.txt
>> +[3] Documentation/devicetree/bindings/leds/leds-lm3633.txt
>> +[4] Documentation/devicetree/bindings/regulator/lm363x-regulator.txt
>
> s/Documentation/devicetree/bindings/../
>
>> +Examples:
>
> These aren't examples, they're actual DT entries.
>
> Please trim them down to just one, fully enabled node, only to be used
> as an 'example'.
>
>> +LM3532 has a backlight device. External GPIO is used for enabling LM3532.
>> +
>> +lm3532@38 {
>> + compatible = "ti,lm3532";
>> + reg = <0x38>;
>> +
>> + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
>> +
>> + backlight {
>> + compatible = "ti,lm3532-backlight";
>> +
>> + lcd {
>> + hvled1-used;
>> + hvled2-used;
>> + hvled3-used;
>> +
>> + ramp-up-msec = <30>;
>> + ramp-down-msec = <0>;
>> +
>> + backlight-max-microamp = <5000>;
>> + };
>> + };
>> +};
>> +
>> +LM3631 has 5 regulators with one backlight device.
>> +
>> +lm3631@29 {
>> + compatible = "ti,lm3631";
>> + reg = <0x29>;
>> +
>> + regulators {
>> + compatible = "ti,lm363x-regulator";
>> +
>> + vboost {
>> + regulator-name = "lcd_boost";
>> + regulator-min-microvolt = <4500000>;
>> + regulator-max-microvolt = <6350000>;
>> + regulator-always-on;
>> + };
>> +
>> + vcont {
>> + regulator-name = "lcd_vcont";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + };
>> +
>> + voref {
>> + regulator-name = "lcd_voref";
>> + regulator-min-microvolt = <4000000>;
>> + regulator-max-microvolt = <6000000>;
>> + };
>> +
>> + vpos {
>> + regulator-name = "lcd_vpos";
>> + regulator-min-microvolt = <4000000>;
>> + regulator-max-microvolt = <6000000>;
>> + regulator-boot-on;
>> + };
>> +
>> + vneg {
>> + regulator-name = "lcd_vneg";
>> + regulator-min-microvolt = <4000000>;
>> + regulator-max-microvolt = <6000000>;
>> + regulator-boot-on;
>> + };
>> + };
>> +
>> + backlight {
>> + compatible = "ti,lm3631-backlight";
>> +
>> + lcd {
>> + backlight-name = "lcd_bl";
>> + hvled1-used;
>> + hvled2-used;
>> +
>> + ramp-up-msec = <300>;
>> + };
>> + };
>> +};
>> +
>> +LM3632 has 3 regulators with one backlight device. External GPIO is
>> +used for enabling LM3632.
>> +
>> +lm3632@11 {
>> + compatible = "ti,lm3632";
>> + reg = <0x11>;
>> +
>> + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
>> +
>> + regulators {
>> + compatible = "ti,lm363x-regulator";
>> +
>> + ti,lcm-en1-gpio = <&pioC 0 GPIO_ACTIVE_HIGH>;
>> + ti,lcm-en2-gpio = <&pioC 1 GPIO_ACTIVE_HIGH>;
>> +
>> + vboost {
>> + regulator-name = "lcd_boost";
>> + regulator-min-microvolt = <4500000>;
>> + regulator-max-microvolt = <6400000>;
>> + regulator-always-on;
>> + };
>> +
>> + vpos {
>> + regulator-name = "lcd_vpos";
>> + regulator-min-microvolt = <4000000>;
>> + regulator-max-microvolt = <6000000>;
>> + };
>> +
>> + vneg {
>> + regulator-name = "lcd_vneg";
>> + regulator-min-microvolt = <4000000>;
>> + regulator-max-microvolt = <6000000>;
>> + };
>> + };
>> +
>> + backlight {
>> + compatible = "ti,lm3632-backlight";
>> +
>> + lcd {
>> + backlight-name = "lcd";
>> + hvled1-used;
>> + hvled2-used;
>> + };
>> + };
>> +};
>> +
>> +LM3633 has multiple backlight channels, LED channels and hardware fault
>> +monitoring driver. External GPIO is used for enabling LM3633.
>> +
>> +lm3633@36 {
>> + compatible = "ti,lm3633";
>> + reg = <0x36>;
>> +
>> + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
>> +
>> + backlight {
>> + compatible = "ti,lm3633-backlight";
>> +
>> + pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */
>> + pwm-names = "lmu-backlight";
>> +
>> + main {
>> + backlight-name = "main_lcd";
>> + hvled2-used;
>> + hvled3-used;
>> + backlight-max-microamp = <20000>;
>> +
>> + ramp-up-msec = <500>;
>> + ramp-down-msec = <500>;
>> + };
>> +
>> + front {
>> + backlight-name = "front_lcd";
>> + hvled1-used;
>> +
>> + ramp-up-msec = <1000>;
>> + ramp-down-msec = <0>;
>> +
>> + pwm-period = <10000>;
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "ti,lm3633-leds";
>> +
>> + chan2 {
>> + channel-name = "status";
>> + lvled2-used;
>> + led-max-microamp = <6000>;
>> + };
>> +
>> + chan456 {
>> + channel-name = "rgb";
>> + lvled4-used;
>> + lvled5-used;
>> + lvled6-used;
>> + };
>> + };
>> +
>> + hwmon {
>> + compatible = "ti,lm3633-hwmon";
>> + };
>> +};
>> +
>> +LM3695 is single backlight device.
>> +
>> +lm3695@63 {
>> + compatible = "ti,lm3695";
>> + reg = <0x63>;
>> +
>> + backlight {
>> + compatible = "ti,lm3695-backlight";
>> +
>> + lcd {
>> + hvled1-used;
>> + hvled2-used;
>> + backlight-max-microamp = <20000>;
>> + };
>> + };
>> +};
>> +
>> +LM3697 has one backlight device and hardware fault monitoring driver.
>> +External GPIO is used for enabling LM3697.
>> +
>> +lm3697@36 {
>> + compatible = "ti,lm3697";
>> + reg = <0x36>;
>> +
>> + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
>> +
>> + backlight {
>> + compatible = "ti,lm3697-backlight";
>> +
>> + pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */
>> + pwm-names = "lmu-backlight";
>> +
>> + lcd {
>> + backlight-name = "bl";
>> + hvled1-used;
>> + hvled2-used;
>> + hvled3-used;
>> + backlight-max-microamp = <20000>;
>> +
>> + ramp-up-msec = <500>;
>> + ramp-down-msec = <500>;
>> + pwm-period = <10000>;
>> + };
>> + };
>> +
>> + hwmon {
>> + compatible = "ti,lm3697-hwmon";
>> + };
>> +};
>


\
 
 \ /
  Last update: 2015-11-12 01:21    [W:0.064 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site