lkml.org 
[lkml]   [2015]   [Jan]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] ARM: AM43xx: hwmod: add VPFE hwmod entries
Hi Benoit,

On Mon, Jan 26, 2015 at 3:50 PM, Benoit Parrot <bparrot@ti.com> wrote:
> Lad, Prabhakar <prabhakar.csengg@gmail.com> wrote on Mon [2015-Jan-26 08:13:01 +0000]:
>> Hi Paul,
>>
>> Thanks for the review.
>>
>> On Mon, Jan 26, 2015 at 2:15 AM, Paul Walmsley <paul@pwsan.com> wrote:
>> > Hi
>> >
>> > On Sun, 25 Jan 2015, Lad, Prabhakar wrote:
>> >
>> >> From: Benoit Parrot <bparrot@ti.com>
>> >>
>> >> this patch adds VPFE HWMOD data for AM43xx.
>> >>
>> >> Signed-off-by: Benoit Parrot <bparrot@ti.com>
>> >> Signed-off-by: Darren Etheridge <detheridge@ti.com>
>> >> Signed-off-by: Felipe Balbi <balbi@ti.com>
>> >> Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
>> >> ---
>> >> Hi Paul,
>> >>
>> >> You were right, the hardware team has confirmed that, the VPFE master port is
>> >> connected to L3 and the VPFE slave port is connected to L4. The L3 port cannot
>> >> serve as a register target because it is initiator only.
>> >
>> > OK makes sense to me.,
>> >
>> >>
>> >> I have created links referring to dss l3/l4 hwmod and tested it, lemme know
>> >> if I have missed something.
>> >
>> > A few minor comments below
>> >
>> >>
>> [Snip]
>> >> /* Interfaces */
>> >> static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
>> >> .master = &am33xx_l3_main_hwmod,
>> >> @@ -788,6 +826,36 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__dss_rfbi = {
>> >> .user = OCP_USER_MPU | OCP_USER_SDMA,
>> >> };
>> >>
>> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
>> >> + .master = &am43xx_vpfe0_hwmod,
>> >> + .slave = &am33xx_l3_main_hwmod,
>> >> + .clk = "l3_gclk",
>> >> + .flags = OCPIF_SWSUP_IDLE,
>> >
>> > OCPIF_SWSUP_IDLE probably isn't needed here. Could you please try without
>> > it?
>> >
>> >> + .user = OCP_USER_MPU | OCP_USER_SDMA,
>> >> +};
>> >> +
>> >> +static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
>> >> + .master = &am43xx_vpfe1_hwmod,
>> >> + .slave = &am33xx_l3_main_hwmod,
>> >> + .clk = "l3_gclk",
>> >> + .flags = OCPIF_SWSUP_IDLE,
>> >
>> > Same point as the above.
>> >
>> Dropped and tested works! posting a v3.
>
> When you tested it without the OCPIF_SWSUP_IDLE, did you go trhough a complete suspend/resume cycle?
> This flag was added early on because otherwise the susbsytem would not go idle without it...
>
> Can you post the console output during a suspend/resume cycle?
>
Ah I didn’t test the suspend/resume will do and post the console log.

Cheers,
--Prabhakar Lad


\
 
 \ /
  Last update: 2015-01-26 17:21    [W:0.796 / U:0.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site