lkml.org 
[lkml]   [2014]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 09/16] tty: serial: 8250_dma: Add a TX trigger workaround for AM33xx
On Thu, Sep 11, 2014 at 02:50:50PM +0200, Sebastian Andrzej Siewior wrote:
> On 09/11/2014 02:32 PM, Peter Hurley wrote:
> > On 09/11/2014 07:42 AM, Sebastian Andrzej Siewior wrote:
> >> I also need a watchdog timer for TX since it seems that on omap3 the
> >> DMA engine suddenly forgets to continue with DMA…
> >
> > One difference I noticed between the omap driver and the 8250 driver is
> > the way modem status interrupts are handled.
> >
> > The omap driver only checks modem status for the UART_IIR_MSI interrupt type.
> > The 8250 driver checks modem status at every interrupt (other than NO_INT).
> >
> > I think the UART_MSR_DCTS bit always reflects that the CTS input has changed
> > between reads of the MSR _even if auto CTS is on_. So perhaps the hardware
> > is being stopped by uart_handle_cts_change() when auto CTS is on?
>
> I doubt that. What I see from a timer debug is that the TX-FIFO level
> is at 0, the DMA transfer for say 1024 bytes start.
> The FIFO is filled to 64bytes and refilled so it doesn't drop below 50.
> At the time of the stall I see that the DMA engine has outstanding
> bytes which it should transfer and the TX FIFO is empty. If hardware
> flow control stops the transfer, I would expect that the DMA engine
> still fills the TX-FIFO until 64 and then waits. But it doesn't.
> Writing bytes into the FIFO leads to bytes beeing sent (and I see them
> on the other side) but the DMA transfer is still on hold. Canceling the
> DMA transfer and re-programming the remaining bytes transfers the
> remaining bytes.
>
> The odd thing is that I only triggered it with "less file". It doesn't
> happen on regular console interaction or "cat large-file". And it only
> triggers on beagle board xm (omap34xx) and I wasn't able to reproduce
> it on am335x or dra7. The latter shares the same DMA engine as beagle
> board xm.

I can still reproduce it on am335x. I can get out of it as soon as
something else gets written to the console though.

# echo "<3>something" >/dev/kmsg

Frans


>
> I remember also that I disabled the HW/SW float control just to make
> sure it is not it.
>
> >
> > Regards,
> > Peter Hurley
> >
> > [The UPF_HARD_FLOW thing was pretty much just done for omap even though
> > 8250 already had auto CTS/auto RTS. Serial core hardware flow control support
> > needs a redo as drivers have pretty much tacked stuff on randomly.]
>
> Sebastian
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-09-11 17:41    [W:0.091 / U:0.876 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site