lkml.org 
[lkml]   [2014]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] dmaengine: qcom_adm: Add device tree binding
Date
Add device tree binding support for the QCOM ADM DMA driver.

Signed-off-by: Andy Gross <agross@codeaurora.org>
---
Documentation/devicetree/bindings/dma/qcom_adm.txt | 62 ++++++++++++++++++++
1 file changed, 62 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/qcom_adm.txt

diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt
new file mode 100644
index 0000000..9bcab91
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt
@@ -0,0 +1,62 @@
+QCOM ADM DMA Controller
+
+Required properties:
+- compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960
+- reg: Address range for DMA registers
+- interrupts: Should contain one interrupt shared by all channels
+- #dma-cells: must be <2>. First cell denotes the channel number. Second cell
+ denotes CRCI (client rate control interface) flow control assignment.
+- clocks: Should contain the core clock and interface clock.
+- clock-names: Must contain "core" for the core clock and "iface" for the
+ interface clock.
+- resets: Must contain an entry for each entry in reset names.
+- reset-names: Must include the following entries:
+ - clk
+ - c0
+ - c1
+ - c2
+- qcom,ee: indicates the security domain identifier used in the secure world.
+
+Example:
+ adm_dma: dma@18300000 {
+ compatible = "qcom,adm";
+ reg = <0x18300000 0x100000>;
+ interrupts = <0 170 0>;
+ #dma-cells = <2>;
+
+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+ clock-names = "core", "iface";
+
+ resets = <&gcc ADM0_RESET>,
+ <&gcc ADM0_C0_RESET>,
+ <&gcc ADM0_C1_RESET>,
+ <&gcc ADM0_C2_RESET>;
+ reset-names = "clk", "c0", "c1", "c2";
+ qcom,ee = <0>;
+ };
+
+DMA clients must use the format descripted in the dma.txt file, using a three
+cell specifier for each channel.
+
+Each dmas request consists of 3 cells:
+ 1. phandle pointing to the DMA controller
+ 2. channel number
+ 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0.
+ The CRCI is used for flow control. It identifies the peripheral device that
+ is the source/destination for the transferred data.
+
+Example:
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ dmas = <&adm_dma 6 9>,
+ <&adm_dma 5 10>;
+ dma-names = "rx", "tx";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation


\
 
 \ /
  Last update: 2014-09-11 05:01    [W:0.096 / U:0.336 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site