lkml.org 
[lkml]   [2014]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v4 1/4] thermal: rockchip: add driver for thermal
Dear Eduardo,

在 2014/9/10 20:46, Eduardo Valentin 写道:
> Hello Caesar,
>
> On Wed, Sep 10, 2014 at 12:39:07PM +0800, Caesar Wang wrote:
>> Dear Eduardo,
>>
>> I'm sorry for it.
>> I just received this message.Maybe my mailbox has a problem.
>
> No problems. You can take your time.
>
>> Thank you for your comments.
>>
>> 在 2014年08月31日 04:09, Eduardo Valentin 写道:
>>> Hello Ceasar,
>>>
>>> On Wed, Sep 03, 2014 at 10:10:36AM +0800, Caesar Wang wrote:
>>>> Thermal is TS-ADC Controller module supports
>>>> user-defined mode and automatic mode.
>>>>
>>>> User-defined mode refers,TSADC all the control signals entirely by
>>>> software writing to register for direct control.
>>>>
>>>> Automaic mode refers to the module automatically poll TSADC output,
>>>> and the results were checked.If you find that the temperature High
>>>> in a period of time,an interrupt is generated to the processor
>>>> down-measures taken;if the temperature over a period of time High,
>>>> the resulting TSHUT gave CRU module,let it reset the entire chip,
>>>> or via GPIO give PMIC.
>>>>
>>>> Signed-off-by: zhaoyifeng <zyf@rock-chips.com>
> I forgot to ask, is zhaoyifeng the correct name or is it a nickname?
:zhaoyifeng is chinese pinyin,Maybe I can correct name :Zhao Yi Feng or
give him a English name:-D .

But his name is zhaoyifeng, so....
>>>> Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
>>>> ---
>>>> drivers/thermal/Kconfig | 9 +
>>>> drivers/thermal/Makefile | 1 +
>>>> drivers/thermal/rockchip_thermal.c | 669 +++++++++++++++++++++++++++++++++++++
>>>> 3 files changed, 679 insertions(+)
>>>> create mode 100644 drivers/thermal/rockchip_thermal.c
>>>>
>>>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>>>> index f9a1386..a00aa1e 100644
>>>> --- a/drivers/thermal/Kconfig
>>>> +++ b/drivers/thermal/Kconfig
>>>> @@ -133,6 +133,15 @@ config SPEAR_THERMAL
>>>> Enable this to plug the SPEAr thermal sensor driver into the Linux
>>>> thermal framework.
>>>>
>>>> +config ROCKCHIP_THERMAL
>>>> + tristate "Rockchip thermal driver"
>>>> + depends on ARCH_ROCKCHIP
>>>> + help
>>>> + Support for Temperature Sensor ADC (TS-ADC) found on Rockchip SoCs.
>>>> + It supports one critical trip point and one passive trip point. The
>>>> + cpufreq is used as the cooling device to throttle CPUs when the
>>>> + passive trip is crossed.
>>>> +
>>>> config RCAR_THERMAL
>>>> tristate "Renesas R-Car thermal driver"
>>>> depends on ARCH_SHMOBILE || COMPILE_TEST
>>>> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
>>>> index de0636a..b48b817 100644
>>>> --- a/drivers/thermal/Makefile
>>>> +++ b/drivers/thermal/Makefile
>>>> @@ -19,6 +19,7 @@ thermal_sys-$(CONFIG_CPU_THERMAL) += cpu_cooling.o
>>>>
>>>> # platform thermal drivers
>>>> obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
>>>> +obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
>>>> obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
>>>> obj-$(CONFIG_KIRKWOOD_THERMAL) += kirkwood_thermal.o
>>>> obj-y += samsung/
>>>> diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
>>>> new file mode 100644
>>>> index 0000000..011f387
>>>> --- /dev/null
>>>> +++ b/drivers/thermal/rockchip_thermal.c
>>>> @@ -0,0 +1,669 @@
>>>> +/*
>>>> + * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
>>>> + *
>>>> + * This program is free software; you can redistribute it and/or modify it
>>>> + * under the terms and conditions of the GNU General Public License,
>>>> + * version 2, as published by the Free Software Foundation.
>>>> + *
>>>> + * This program is distributed in the hope it will be useful, but WITHOUT
>>>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>>>> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
>>>> + * more details.
>>>> + *
>>>> +*/
>>>> +
>>>> +#include <linux/clk.h>
>>>> +#include <linux/io.h>
>>>> +#include <linux/interrupt.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/of.h>
>>>> +#include <linux/of_address.h>
>>>> +#include <linux/of_irq.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/regulator/consumer.h>
>>>> +#include <linux/cpu_cooling.h>
>>>> +#include "thermal_core.h"
>>> Why do you need thermal_core.h here? Wouldn't linux/thermal.h be
>>> sufficient?
>> yes, I will use linux/thermal.h.
>>>> +
>>>> +enum rockchip_thermal_trip {
>>>> + ROCKCHIP_TRIP_PASSIVE,
>>>> + ROCKCHIP_TRIP_CRITICAL,
>>>> + ROCKCHIP_TRIP_NUM,
>>>> +};
>>>> +
>>> Why do you need your own trip types?
>>>
>>>> +struct rockchip_thermal_data {
>>>> + const struct rockchip_tsadc_platform_data *pdata;
>>>> + struct thermal_zone_device *tz;
>>>> + struct thermal_cooling_device *cdev;
>>>> + enum thermal_device_mode mode;
>>>> + void __iomem *regs;
>>>> +
>>>> + signed long temp_passive;
>>>> + signed long temp_critical;
>>>> + signed long temp_force_shut;
>>>> + signed long alarm_temp;
>>>> + signed long last_temp;
>>>> + bool irq_enabled;
>>>> + int irq;
>>>> + struct clk *clk;
>>>> + struct clk *pclk;
>>>> +};
>>>> +
>>>> +struct rockchip_tsadc_platform_data {
>>>> + u8 irq_en;
>>>> + signed long temp_passive;
>>>> + signed long temp_critical;
>>>> + signed long temp_force_shut;
>>>> + int passive_delay;
>>>> + int polling_delay;
>>>> +
>>>> + int (*irq_handle)(void __iomem *reg);
>>>> + int (*initialize)(void __iomem *reg, signed long temp_force_shut);
>>>> + int (*control)(void __iomem *reg, bool on);
>>>> + u32 (*code_to_temp)(int temp);
>>>> + u32 (*temp_to_code)(int temp);
>>>> + void (*set_alarm_temp)(void __iomem *regs, signed long temp);
>>>> +};
>>>> +
>>>> +/*TSADC V2 Sensor info define:*/
>>>> +#define TSADCV2_AUTO_CON 0x04
>>>> +#define TSADCV2_INT_EN 0x08
>>>> +#define TSADCV2_INT_PD 0x0c
>>>> +#define TSADCV2_DATA1 0x24
>>>> +#define TSADCV2_COMP1_INT 0x34
>>>> +#define TSADCV2_COMP1_SHUT 0x44
>>>> +#define TSADCV2_AUTO_PERIOD 0x68
>>>> +#define TSADCV2_AUTO_PERIOD_HT 0x6c
>>>> +
>>>> +#define TSADCV2_AUTO_SRC1_EN (1 << 5)
>>>> +#define TSADCV2_AUTO_EN (1 << 0)
>>>> +#define TSADCV2_AUTO_DISABLE ~(1 << 0)
>>>> +#define TSADCV2_AUTO_STAS_BUSY (1 << 16)
>>>> +#define TSADCV2_AUTO_STAS_BUSY_MASK (1 << 16)
>>>> +#define TSADCV2_SHUT_2GPIO_SRC1_EN (1 << 5)
>>>> +#define TSADCV2_INT_SRC1_EN (1 << 1)
>>>> +#define TSADCV2_SHUT_SRC1_STATUS (1 << 5)
>>>> +#define TSADCV2_INT_SRC1_STATUS (1 << 1)
>>>> +
>>> The above bits can be defined with BIT() macro, right?
>> Yes. The Bit() will be more resonable..
>>> Something like:
>>> +#define TSADCV2_INT_SRC1_STATUS BIT(1)
>>>
>>>
>>>> +#define TSADCV2_DATA_MASK 0xfff
>>>> +#define TSADCV2_HIGHT_INT_DEBOUNCE 0x60
>>>> +#define TSADCV2_HIGHT_TSHUT_DEBOUNCE 0x64
>>>> +#define TSADCV2_HIGHT_INT_DEBOUNCE_TIME 0x0a
>>>> +#define TSADCV2_HIGHT_TSHUT_DEBOUNCE_TIME 0x0a
>>>> +#define TSADCV2_AUTO_PERIOD_TIME 0x03e8
>>>> +#define TSADCV2_AUTO_PERIOD_HT_TIME 0x64
>>>> +
>>>> +struct tsadc_table {
>>>> + int code;
>>>> + int temp;
>>>> +};
>>>> +
>>>> +static const struct tsadc_table v2_code_table[] = {
>>>> + {TSADCV2_DATA_MASK, -40},
>>>> + {3800, -40},
>>>> + {3792, -35},
>>>> + {3783, -30},
>>>> + {3774, -25},
>>>> + {3765, -20},
>>>> + {3756, -15},
>>>> + {3747, -10},
>>>> + {3737, -5},
>>>> + {3728, 0},
>>>> + {3718, 5},
>>>> + {3708, 10},
>>>> + {3698, 15},
>>>> + {3688, 20},
>>>> + {3678, 25},
>>>> + {3667, 30},
>>>> + {3656, 35},
>>>> + {3645, 40},
>>>> + {3634, 45},
>>>> + {3623, 50},
>>>> + {3611, 55},
>>>> + {3600, 60},
>>>> + {3588, 65},
>>>> + {3575, 70},
>>>> + {3563, 75},
>>>> + {3550, 80},
>>>> + {3537, 85},
>>>> + {3524, 90},
>>>> + {3510, 95},
>>>> + {3496, 100},
>>>> + {3482, 105},
>>>> + {3467, 110},
>>>> + {3452, 115},
>>>> + {3437, 120},
>>>> + {3421, 125},
>>>> + {0, 125},
>>>> +};
>>>> +
>>>> +static int rk_tsadcv2_irq_handle(void __iomem *regs)
>>>> +{
>>>> + u32 val;
>>>> +
>>>> + val = readl_relaxed(regs + TSADCV2_INT_PD);
>>>> + writel_relaxed(val & ~(1 << 8), regs + TSADCV2_INT_PD);
>>> Why do you need to clear bit 8? Why hardcoded?
>> The bit 8 set 0 to clear the interrupt.
>>
> Would it make sense to create a macro for this?

OK .
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static u32 rk_tsadcv2_temp_to_code(int temp)
>>>> +{
>>>> + int i;
>>>> +
>>>> + for (i = 0; i < ARRAY_SIZE(v2_code_table) - 1; i++) {
>>>> + if (temp <= v2_code_table[i].temp && temp >
>>>> + v2_code_table[i - 1].temp)
>>>> + return v2_code_table[i].code;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static u32 rk_tsadcv2_code_to_temp(int code)
>>>> +{
>>>> + int i;
>>>> +
>>>> + for (i = 0; i < ARRAY_SIZE(v2_code_table) - 1; i++) {
>>>> + if (code <= v2_code_table[i].code && code >
>>>> + v2_code_table[i + 1].code){
>>>> + return v2_code_table[i].temp;
>>>> + }
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>> I know the table is not something too big, but considering it is ordered
>>> by either ADC value code or by temp, at least one of the above searching function
>>> may be more efficient, right?
>> Yes, use the point will be more efficient.
>>>> +
>>>> +static int rk_tsadcv2_initialize(void __iomem *regs,
>>>> + signed long temp_force_shut)
>>>> +{
>>>> + int shutdown_value;
>>>> +
>>>> + shutdown_value = rk_tsadcv2_temp_to_code(temp_force_shut);
>>>> + /* Enable measurements at ~ 10 Hz */
>>> Does it leave the sampling clock at 10Hz?
>> yes.
> ok
>
>
>>> Is this clock exposed via
>>> clock framework?
>> The clock is divided by data->clk.
> ok
>
>>>> + writel_relaxed(0, regs + TSADCV2_AUTO_CON);
>>>> + writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD);
>>>> + writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, regs +
>>>> + TSADCV2_AUTO_PERIOD_HT);
>>>> + writel_relaxed(shutdown_value, regs + TSADCV2_COMP1_SHUT);
>>>> + writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_TIME, regs +
>>>> + TSADCV2_HIGHT_INT_DEBOUNCE);
>>>> + writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_TIME, regs +
>>>> + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
>>>> + writel_relaxed(TSADCV2_SHUT_2GPIO_SRC1_EN | TSADCV2_INT_SRC1_EN, regs +
>>>> + TSADCV2_INT_EN);
>>>> + writel_relaxed(TSADCV2_AUTO_SRC1_EN | TSADCV2_AUTO_EN, regs +
>>>> + TSADCV2_AUTO_CON);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rk_tsadcv2_control(void __iomem *regs, bool on)
>>>> +{
>>>> + u32 val;
>>>> +
>>>> + if (on) {
>>>> + val = readl_relaxed(regs + TSADCV2_AUTO_CON);
>>>> + writel_relaxed(val | TSADCV2_AUTO_EN, regs + TSADCV2_AUTO_CON);
>>>> + } else {
>>>> + val = readl_relaxed(regs + TSADCV2_AUTO_CON);
>>>> + writel_relaxed(val & TSADCV2_AUTO_DISABLE,
>>>> + regs + TSADCV2_AUTO_CON);
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static void rk_tsadcv2_alarm_temp(void __iomem *regs, signed long alarm_temp)
>>>> +{
>>>> + int alarm_value;
>>>> +
>>>> + alarm_value = rk_tsadcv2_temp_to_code(alarm_temp);
>>>> + writel_relaxed(alarm_value, regs + TSADCV2_COMP1_INT);
>>>> +}
>>>> +
>>>> +struct rockchip_tsadc_platform_data const rk3288_tsadc_data = {
>>>> + .irq_en = 1,
>>>> + .temp_passive = 85000,
>>>> + .temp_critical = 100000,
>>>> + .temp_force_shut = 120000,
>>>> + .passive_delay = 2000,
>>>> + .polling_delay = 1000,
>>>> + .irq_handle = rk_tsadcv2_irq_handle,
>>>> + .initialize = rk_tsadcv2_initialize,
>>>> + .control = rk_tsadcv2_control,
>>>> + .code_to_temp = rk_tsadcv2_code_to_temp,
>>>> + .temp_to_code = rk_tsadcv2_temp_to_code,
>>>> + .set_alarm_temp = rk_tsadcv2_alarm_temp,
>>>> +};
>>> shall the above struct be also static?
>> OK.
>>>> +
>>>> +static const struct of_device_id of_rockchip_thermal_match[] = {
>>>> + {
>>>> + .compatible = "rockchip,rk3288-tsadc",
>>>> + .data = (void *)&rk3288_tsadc_data,
>>>> + },
>>>> + { /* end */ },
>>>> +};
>>>> +MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match);
>>>> +
>>>> +static void rockchip_set_alarm_temp(struct rockchip_thermal_data *data,
>>>> + signed long alarm_temp)
>>>> +{
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> +
>>>> + data->alarm_temp = alarm_temp;
>>>> + if (p_tsadc_data->set_alarm_temp)
>>>> + p_tsadc_data->set_alarm_temp(data->regs, alarm_temp);
>>>> +}
>>>> +
>>>> +static int rockchip_get_temp(struct thermal_zone_device *tz,
>>>> + unsigned long *temp)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> + u32 val;
>>>> +
>>>> + val = readl_relaxed(data->regs + TSADCV2_DATA1);
>>>> + *temp = p_tsadc_data->code_to_temp(val);
>>>> +
>>>> + /* Update alarm value to next higher trip point */
>>>> + if (data->alarm_temp == data->temp_passive && *temp >=
>>>> + data->temp_passive)
>>>> + rockchip_set_alarm_temp(data, data->temp_critical);
>>>> +
>>>> + if (data->alarm_temp == data->temp_critical && *temp <
>>>> + data->temp_passive) {
>>>> + rockchip_set_alarm_temp(data, data->temp_passive);
>>>> + dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
>>>> + data->alarm_temp / 1000);
>>>> + }
>>>> +
>>>> + if (*temp != data->last_temp) {
>>>> + dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
>>>> + data->last_temp = *temp;
>>>> + }
>>>> +
>>>> + /* Reenable alarm IRQ if temperature below alarm temperature */
>>>> + if (!data->irq_enabled && *temp < data->alarm_temp) {
>>>> + data->irq_enabled = true;
>>>> + enable_irq(data->irq);
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_thermal_initialize(struct rockchip_thermal_data *data)
>>>> +{
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> +
>>>> + if (p_tsadc_data->initialize)
>>>> + p_tsadc_data->initialize(data->regs, data->temp_force_shut);
>>>> + rockchip_set_alarm_temp(data, data->temp_passive);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static void rockchip_thermal_control(struct rockchip_thermal_data *data,
>>>> + bool on)
>>>> +{
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> +
>>>> + if (p_tsadc_data->control)
>>>> + p_tsadc_data->control(data->regs, on);
>>>> +
>>>> + if (on) {
>>>> + data->irq_enabled = true;
>>>> + data->mode = THERMAL_DEVICE_ENABLED;
>>>> + } else {
>>>> + data->irq_enabled = false;
>>>> + data->mode = THERMAL_DEVICE_DISABLED;
>>>> + }
>>>> +}
>>>> +
>>>> +static int rockchip_get_mode(struct thermal_zone_device *tz,
>>>> + enum thermal_device_mode *mode)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> +
>>>> + *mode = data->mode;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_set_mode(struct thermal_zone_device *tz,
>>>> + enum thermal_device_mode mode)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> +
>>>> + if (mode == THERMAL_DEVICE_ENABLED) {
>>>> + tz->polling_delay = p_tsadc_data->polling_delay;
>>>> + tz->passive_delay = p_tsadc_data->passive_delay;
>>>> + if (!data->irq_enabled) {
>>>> + data->irq_enabled = true;
>>>> + enable_irq(data->irq);
>>>> + }
>>>> + } else {
>>>> + tz->polling_delay = 0;
>>>> + tz->passive_delay = 0;
>>>> + if (data->irq_enabled) {
>>>> + disable_irq(data->irq);
>>>> + data->irq_enabled = false;
>>>> + }
>>>> + }
>>>> +
>>>> + data->mode = mode;
>>>> + thermal_zone_device_update(tz);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_get_trip_type(struct thermal_zone_device *tz, int trip,
>>>> + enum thermal_trip_type *type)
>>>> +{
>>>> + *type = (trip == ROCKCHIP_TRIP_PASSIVE) ? THERMAL_TRIP_PASSIVE :
>>>> + THERMAL_TRIP_CRITICAL;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_get_crit_temp(struct thermal_zone_device *tz,
>>>> + unsigned long *temp)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> +
>>>> + *temp = data->temp_critical;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_get_trip_temp(struct thermal_zone_device *tz, int trip,
>>>> + unsigned long *temp)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> +
>>>> + *temp = (trip == ROCKCHIP_TRIP_PASSIVE) ? data->temp_passive :
>>>> + data->temp_critical;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_set_trip_temp(struct thermal_zone_device *tz, int trip,
>>>> + unsigned long temp)
>>>> +{
>>>> + struct rockchip_thermal_data *data = tz->devdata;
>>>> +
>>>> + if (trip == ROCKCHIP_TRIP_CRITICAL)
>>>> + return -EPERM;
>>>> +
>>>> + data->temp_passive = temp;
>>>> + rockchip_set_alarm_temp(data, temp);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_bind(struct thermal_zone_device *tz,
>>>> + struct thermal_cooling_device *cdev)
>>>> +{
>>>> + int ret;
>>>> +
>>>> + ret = thermal_zone_bind_cooling_device(tz, ROCKCHIP_TRIP_PASSIVE, cdev,
>>>> + THERMAL_NO_LIMIT,
>>>> + THERMAL_NO_LIMIT);
>>>> + if (ret) {
>>>> + dev_err(&tz->device, "binding zone %s with cdev %s failed:%d\n",
>>>> + tz->type, cdev->type, ret);
>>>> + return ret;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_unbind(struct thermal_zone_device *tz,
>>>> + struct thermal_cooling_device *cdev)
>>>> +{
>>>> + int ret;
>>>> +
>>>> + ret = thermal_zone_unbind_cooling_device(tz,
>>>> + ROCKCHIP_TRIP_PASSIVE, cdev);
>>>> + if (ret) {
>>>> + dev_err(&tz->device,
>>>> + "unbinding zone %s with cdev %s failed:%d\n", tz->type,
>>>> + cdev->type, ret);
>>>> + return ret;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>> The method of binding and unbinding used above requires you to check if
>>> you are binding to the right cdev. If in your system you register more
>>> than one cdev, say someone loads the power supply core, which in turns
>>> register a cooling device for charging, your thermal zone will bind it
>>> to TRIP_PASSIVE. It will happen to any cooling device that eventually
>>> gets registered to the thermal framework. Is that the desired outcome?
>> Yes,I will use the generic trip points in the dts and fix it in the
>> thermal driver.
> great
>
>>> If not, you may want to compare the paramenter cdev to your data->cdev.
>>>
>>>> +
>>>> +static struct thermal_zone_device_ops rockchip_tz_ops = {
>>>> + .bind = rockchip_bind,
>>>> + .unbind = rockchip_unbind,
>>>> + .get_temp = rockchip_get_temp,
>>>> + .get_mode = rockchip_get_mode,
>>>> + .set_mode = rockchip_set_mode,
>>>> + .get_trip_type = rockchip_get_trip_type,
>>>> + .get_trip_temp = rockchip_get_trip_temp,
>>>> + .get_crit_temp = rockchip_get_crit_temp,
>>>> + .set_trip_temp = rockchip_set_trip_temp,
>>>> +};
>>>> +
>>>> +static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev)
>>>> +{
>>>> + struct rockchip_thermal_data *data = data;
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data = data->pdata;
>>>> +
>>>> + dev_dbg(&data->tz->device, "THERMAL ALARM: T > %lu\n",
>>>> + data->alarm_temp / 1000);
>>>> +
>>>> + if (p_tsadc_data->irq_en && p_tsadc_data->irq_handle)
>>>> + p_tsadc_data->irq_handle(data->regs);
>>>> +
>>>> + thermal_zone_device_update(data->tz);
>>>> +
>>>> + return IRQ_HANDLED;
>>>> +}
>>>> +
>>>> +static int rockchip_thermal_probe(struct platform_device *pdev)
>>>> +{
>>>> + struct rockchip_thermal_data *data;
>>>> + const struct rockchip_tsadc_platform_data *p_tsadc_data;
>>>> + struct cpumask clip_cpus;
>>>> + struct resource *res;
>>>> + const struct of_device_id *match;
>>>> + int ret, temp;
>>>> +
>>>> + data = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data),
>>>> + GFP_KERNEL);
>>>> + if (!data)
>>>> + return -ENOMEM;
>>>> +
>>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>>> + data->regs = devm_ioremap_resource(&pdev->dev, res);
>>>> + if (IS_ERR(data->regs)) {
>>>> + dev_err(&pdev->dev, "Could not get tsadc source, %p\n",
>>>> + data->regs);
>>>> + return PTR_ERR(data->regs);
>>>> + }
>>>> +
>>>> + match = of_match_node(of_rockchip_thermal_match, pdev->dev.of_node);
>>>> + if (!match)
>>>> + return -ENXIO;
>>>> + data->pdata = (const struct rockchip_tsadc_platform_data *)match->data;
>>>> + if (!data->pdata)
>>>> + return -EINVAL;
>>>> + p_tsadc_data = data->pdata;
>>>> +
>>>> + data->clk = devm_clk_get(&pdev->dev, "tsadc");
>>>> + if (IS_ERR(data->clk)) {
>>>> + dev_err(&pdev->dev, "failed to get tsadc clock\n");
>>>> + return PTR_ERR(data->clk);
>>>> + }
>>>> +
>>>> + data->pclk = devm_clk_get(&pdev->dev, "apb_pclk");
>>>> + if (IS_ERR(data->pclk)) {
>>>> + dev_err(&pdev->dev, "failed to get tsadc pclk\n");
>>>> + return PTR_ERR(data->pclk);
>>>> + }
>>>> +
>>>> + /*
>>>> + * Use a default of 10KHz for the converter clock.
>>>> + * This may become user-configurable in the future.
>>>> + */
>>>> + ret = clk_set_rate(data->clk, 10000);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev, "failed to set tsadc clk rate, %d\n", ret);
>>>> + return ret;
>>>> + }
>>>> +
>>>> + ret = clk_prepare_enable(data->clk);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev, "failed to enable converter clock\n");
>>>> + goto err_clk;
>>>> + }
>>>> +
>>>> + ret = clk_prepare_enable(data->pclk);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev, "failed to enable pclk\n");
>>>> + goto err_pclk;
>>>> + }
>>>> +
>>>> + platform_set_drvdata(pdev, data);
>>>> +
>>>> + if (of_property_read_u32(pdev->dev.of_node, "passive-temp", &temp)) {
>>>> + dev_warn(&pdev->dev,
>>>> + "Missing default passive temp property in the DT.\n");
>>>> + data->temp_passive = p_tsadc_data->temp_passive;
>>>> + } else {
>>>> + data->temp_passive = temp;
>>>> + }
>>>> +
>>>> + if (of_property_read_u32(pdev->dev.of_node, "critical-temp", &temp)) {
>>>> + dev_warn(&pdev->dev,
>>>> + "Missing default critical temp property in the DT.\n");
>>>> + data->temp_critical = p_tsadc_data->temp_critical;
>>>> + } else {
>>>> + data->temp_critical = temp;
>>>> + }
>>>> +
>>>> + if (of_property_read_u32(pdev->dev.of_node, "force-shut-temp", &temp)) {
>>>> + dev_warn(&pdev->dev,
>>>> + "Missing default force shut down temp property in the DT.\n");
>>>> + data->temp_force_shut = p_tsadc_data->temp_force_shut;
>>>> + } else {
>>>> + data->temp_force_shut = temp;
>>>> + }
>>>> +
>>>> + cpumask_set_cpu(0, &clip_cpus);
>>>> + data->cdev = of_cpufreq_cooling_register(pdev->dev.of_node, &clip_cpus);
>>>> + if (IS_ERR(data->cdev)) {
>>>> + dev_err(&pdev->dev, "failed to register cpufreq cooling device\n");
>>>> + goto disable_clk;
>>>> + }
>>>> +
>>>> + data->tz = thermal_zone_device_register("rockchip_thermal",
>>>> + ROCKCHIP_TRIP_NUM,
>>>> + 0, data,
>>>> + &rockchip_tz_ops, NULL,
>>>> + p_tsadc_data->passive_delay,
>>>> + p_tsadc_data->polling_delay);
>>>> +
>>>> + if (IS_ERR(data->tz)) {
>>>> + dev_err(&pdev->dev, "failed to register thermal zone device\n");
>>>> + goto fail_cpufreq_register;
>>>> + }
>>>> +
>>>> + if (p_tsadc_data->irq_en) {
>>>> + data->irq = platform_get_irq(pdev, 0);
>>>> + if (data->irq < 0) {
>>>> + dev_err(&pdev->dev, "no irq resource?\n");
>>>> + goto fail_irq;
>>>> + }
>>>> +
>>>> + ret = devm_request_threaded_irq(&pdev->dev, data->irq, NULL,
>>>> + rockchip_thermal_alarm_irq_thread,
>>>> + IRQF_ONESHOT, "rockchip_thermal", data);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev,
>>>> + "failed to request tsadc irq: %d\n", ret);
>>>> + goto fail_thermal_unregister;
>>>> + }
>>>> + }
>>>> +
>>>> + rockchip_thermal_initialize(data);
>>>> + rockchip_thermal_control(data, true);
>>>> +
>>>> + return 0;
>>>> +
>>>> +fail_thermal_unregister:
>>>> + thermal_zone_device_unregister(data->tz);
>>>> +fail_irq:
>>>> +fail_cpufreq_register:
>>>> + cpufreq_cooling_unregister(data->cdev);
>>>> +disable_clk:
>>>> +err_pclk:
>>>> + clk_disable_unprepare(data->pclk);
>>>> +err_clk:
>>>> + clk_disable_unprepare(data->clk);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +static int rockchip_thermal_remove(struct platform_device *pdev)
>>>> +{
>>>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>>>> +
>>>> + rockchip_thermal_control(data, false);
>>>> +
>>>> + thermal_zone_device_unregister(data->tz);
>>>> + cpufreq_cooling_unregister(data->cdev);
>>>> + cpufreq_cooling_unregister(data->cdev);
>>>> +
>>> The above call is duplicated.
>> OK.
>>>> + clk_disable_unprepare(data->clk);
>>>> + clk_disable_unprepare(data->pclk);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +#ifdef CONFIG_PM_SLEEP
>>>> +static int rockchip_thermal_suspend(struct device *dev)
>>>> +{
>>>> + struct platform_device *pdev = to_platform_device(dev);
>>>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>>>> +
>>>> + rockchip_thermal_control(data, false);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rockchip_thermal_resume(struct device *dev)
>>>> +{
>>>> + struct platform_device *pdev = to_platform_device(dev);
>>>> + struct rockchip_thermal_data *data = platform_get_drvdata(pdev);
>>>> +
>>>> + rockchip_thermal_initialize(data);
>>>> + rockchip_thermal_control(data, true);
>>>> +
>>>> + return 0;
>>>> +}
>>> Would you need to manage your clocks too in the suspend resume path
>>> (data->clk and data->pclk)?
>> yes.
>> Usually,it's need disable to save power.
> Yes, that's my point. Please consider handling clocks to improve power
> savings.
>
>>>> +#endif
>>>> +
>>>> +static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops,
>>>> + rockchip_thermal_suspend, rockchip_thermal_resume);
>>>> +
>>>> +static struct platform_driver rockchip_thermal_driver = {
>>>> + .driver = {
>>>> + .name = "rockchip-thermal",
>>>> + .owner = THIS_MODULE,
>>>> + .pm = &rockchip_thermal_pm_ops,
>>>> + .of_match_table = of_rockchip_thermal_match,
>>>> + },
>>>> + .probe = rockchip_thermal_probe,
>>>> + .remove = rockchip_thermal_remove,
>>>> +};
>>>> +
>>>> +module_platform_driver(rockchip_thermal_driver);
>>>> +
>>>> +MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver");
>>>> +MODULE_AUTHOR("Rockchip, Inc.");
>>>> +MODULE_LICENSE("GPL");
>>> Your file header states GPL version two. Thus I suppose you meant:
>>> +MODULE_LICENSE("GPL v2");
>>>
>>> right?
>>>
>>> Check include/linux/module.h for further clarifications.
>> But I think the "GPL" is support for thr GNU Public License v2 or later.
> Exactly, if you intend to support v3, then it is fine. But your code
> header states only V2.
>
>> I will fix GPL v2 if I get it wrong.
> If your license is GPLv2 only as mentioned in your header, please use 'GPL
> v2' tag.
>
> Cheers,
>
>>>> +MODULE_ALIAS("platform:rockchip-thermal");
>>>> --
>>>> 1.9.1
>>>>
>>>>
>>> BR,
>>>
>>> Eduardo Valentin
>>>
>>>
>>>
>> --
>> Best regards,
>> Caesar
>>
>>
>
>

--
Best regards,
Caesar


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-09-10 16:01    [W:0.095 / U:0.788 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site