Messages in this thread | | | Date | Wed, 20 Aug 2014 11:48:08 +0200 | From | Thierry Reding <> | Subject | Re: [PATCH 3/3] ARM: at91/tclib: mask interruptions at shutdown and probe |
| |
On Wed, Aug 20, 2014 at 11:06:25AM +0200, Boris BREZILLON wrote: > On Wed, 20 Aug 2014 10:28:20 +0200 > Thierry Reding <thierry.reding@gmail.com> wrote: > > > On Wed, Aug 20, 2014 at 10:14:22AM +0200, Boris BREZILLON wrote: > > > Hi Thierry, > > > > > > On Wed, 20 Aug 2014 09:31:13 +0200 > > > Thierry Reding <thierry.reding@gmail.com> wrote: > > > > > > > On Wed, Aug 20, 2014 at 01:01:30AM +0200, Boris BREZILLON wrote: > > > > > Hi Jean-Christophe, > > > > > > > > > > On Wed, 20 Aug 2014 06:11:17 +0800 > > > > > Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> wrote: > > > > > > > > > > > Hi, > > > > > > > > > > > > This is a bit weird as the clock of the TC should be off and the irq free > > > > > > > > > > > > so this should never happened we need to investigate more why this append > > > > > > > > > > I may have found the source of this bug. > > > > > > > > > > As Gael stated, when you're kexec-ing a new kernel your previous kernel > > > > > could be using the tbc_clksrc driver (and especially the clkevent > > > > > device). Thus the kernel might have planned a timer event and then been > > > > > asked to shutdown the machine (requested by the kexec code). > > > > > In this case the AIC interrupt connected to the TC Block is disabled > > > > > but not the interrupts within the TCB IP (IDR registers), possibly > > > > > leaving a pending interrupt before booting the new kernel. > > > > > > > > > > When the tcb_clksrc driver is loaded by the new kernel it enables the > > > > > interrupt line by calling setup_irq [1] while the clockevent device is > > > > > not registered yet [2]. Thus the event_handler is still NULL when the > > > > > AIC line connected to the TCB is unmasked. Remember that an interrupt > > > > > is still pending on this HW block, which will lead to an immediate call > > > > > to the ch2_irq handler, which tries to call the event_handler, which in > > > > > turns is NULL because clkevent device registration has not taken place > > > > > at this moment => Kernel panic. > > > > > ITOH, we can't register the clkevent device before the irq handler is > > > > > set up, because we should be ready to handle clkevent request at the > > > > > time clockevents_config_and_register is called. > > > > > > > > > > This leaves two solution: > > > > > 1) disable the TCB irqs (using TCB IDR registers) before calling > > > > > setup_irq in the tcb_clksrc driver > > > > > 2) disable the TCB irqs at the tclib level (as proposed by Gael) > > > > > > > > > > I prefer solution #2 because it fixes the bug for all TCB users (not > > > > > just the tcb_clksrc driver). > > > > > > > > Wouldn't a more proper fix be to only enable the IRQ (setup_irq()) once > > > > everything has properly been set up? That's certainly how all other > > > > drivers are doing this. Generally I think it's best to assume that an > > > > interrupt can fire at any point after it's been enabled, so everything > > > > should be set up prior to enabling it. > > > > > > Sure. And, AFAIK, another common practice is to disable all interrupts > > > and acknowledge all pending interrupts before registering a new irq > > > handler to avoid inheriting peripheral dirty state from previous usage > > > (either the bootloader, or the previous kernel when using kexec). > > > > Discarding all pending interrupts may not always be what we want. And > > masking interrupts prior to registering the handler isn't always going > > to work either (shared interrupts), so device drivers should always set > > things up in the correct order. > > > > I meant disabling/acknowledging interrupts within the HW block not > the interrupt line connected to the interrupt controller (which indeed > can be shared among several peripherals). > The TCB IP provides SR (Status Register) to acknowledge interrupts at > the TCB level and IER/IDR/ISR (Interrupt Enable/Disable/Status > Register) to manipulate TCB interrupts.
But when you share interrupts, then when an incoming interrupt will cause all handlers to be called, so you still need to set it up properly.
Thierry [unhandled content-type:application/pgp-signature] | |