lkml.org 
[lkml]   [2014]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [alsa-devel] [PATCH V1 1/3] ASoC: fsl: Kconfig: remove dependence of SND_IMX_SOC for SND_SOC_IMX_PCM_DMA
Date
> Subject: Re: [alsa-devel] [PATCH V1 1/3] ASoC: fsl: Kconfig: remove dependence
> of SND_IMX_SOC for SND_SOC_IMX_PCM_DMA
>
> On Mon, Aug 18, 2014 at 06:52:46PM +0200, Lars-Peter Clausen wrote:
> > On 08/18/2014 10:38 AM, Shengjiu Wang wrote:
> > >Build kernel with SND_SOC_IMC_PCM_DMA=m && SND_IMX_SOC=n leads the
> following
> > >error:
> > >
> > > sound/built-in.o: In function `fsl_sai_probe':
> > >>>fsl_sai.c:(.text+0x5f662): undefined reference to `imx_pcm_dma_init'
> > > sound/built-in.o: In function `fsl_esai_probe':
> > >>>fsl_esai.c:(.text+0x6044b): undefined reference to `imx_pcm_dma_init'
> > >
> > >Most cpu driver in soc/fsl has use the function 'imx_pcm_dma_init' which is
> > >defined in imx-pcm-dma.c, so need to select SND_SOC_IMX_PCM_DMA, but it
> depends
> > >on SND_IMX_SOC, if SND_IMX_SOC=n, then SND_SOC_IMX_PCM_DMA will not be
> > >selected.
> > >So remove the dependence of SND_IMX_SOC for SND_SOC_IMX_PCM_DMA.
> > >
> > >Reported-by: kbuild test robot <fengguang.wu@intel.com>
> > >Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
> >
> > Those if conditions where just added[1] by Arnd to avoid other build
> > failures. So just removing them again makes little sense.
> >
> > As far as I can see imx_pcm_dma_init() should be stubbed out when
> > SND_SOC_IMX_PCM_DMA is not selected. So what's going on here?
> >
> > [1]
> http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=ff40
> 260f79dc0436604452bccd449bffd25ebafb
> >
> Lars-Peter Clausen & Arnd
>
> The purpose of Arnd's patch is same with me, which is to resolve the build
> error when SND_SOC_IMX_PCM_DMA=m & SND_SOC_FSL_SSI/SAI/ESAI/SPDIF=y, the
> error is "undefined reference to `imx_pcm_dma_init'".
> But Arnd's patch didn't involve this situation that SND_IMX_SOC=n &
> SND_SOC_IMX_PCM_DMA=m.
>
> Currently I think out a solution for this issue is to change
>
> select SND_SOC_IMX_PCM_DMA if SND_IMX_SOC != n
>
> to
>
> depends on SND_SOC_IMX_PCM_DMA != m
>
> How do you think about this?
>

What will happen if to build both SAI/ESAI and IMX_PCM_DMA as modules at the same
time ?

Thanks,

BRs
Xiubo


> best regards
> Wang shengjiu


\
 
 \ /
  Last update: 2014-08-19 10:21    [W:0.176 / U:0.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site