lkml.org 
[lkml]   [2014]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 6/6] thermal: Add Tegra SOCTHERM thermal management driver
On 04/07/14 11:43, Wei Ni wrote:
> On 06/27/2014 04:11 PM, Mikko Perttunen wrote:
>> This adds support for the Tegra SOCTHERM thermal sensing and management
>> system found in the Tegra124 system-on-chip. This initial driver supports
>> the four thermal zones with hardware-tracked trip points.
>
>> diff --git a/drivers/thermal/tegra_soctherm.c b/drivers/thermal/tegra_soctherm.c
>
>> +static int calculate_shared_calibration(struct tsensor_shared_calibration *r)
>> +{
>> + u32 val;
>> + u32 shifted_cp, shifted_ft;
>> + int err;
>> +
>> + err = tegra_fuse_readl(FUSE_TSENSOR8_CALIB, &val);
>> + if (err)
>> + return err;
>> + r->base_cp = val & 0x3ff;
>> + r->base_ft = (val & (0x7ff << 10)) >> 10;
>> +
>> + err = tegra_fuse_readl(FUSE_SPARE_REALIGNMENT_REG_0, &val);
>> + if (err)
>> + return err;
>> + /* Sign extend from 6 bits to 32 bits */
>> + shifted_cp = (s32)((val & 0x1f) | ((val & 0x20) ? 0xffffffe0 : 0x0));
>> + val = ((val & (0x1f << 21)) >> 21);
>> + /* Sign extend from 5 bits to 32 bits */
>> + shifted_ft = (s32)((val & 0xf) | ((val & 0x10) ? 0xfffffff0 : 0x0));
>> +
>> + r->actual_temp_cp = 2 * 25 + shifted_cp;
> Do we need to define the "25" as constant, just like below line.

I believe downstream just uses "25" which is the reason I used it, but
yes, a constant would be nicer.

>
>> + r->actual_temp_ft = 2 * NOMINAL_CALIB_FT_T124 + shifted_ft;
>> +
>> + return 0;
>> +}
>
>> +
>> +static irqreturn_t soctherm_isr(int irq, void *dev_id)
>> +{
>> + struct tegra_thermctl_zone *zone = dev_id;
>> + u32 val;
>> + u32 intr_mask = 0x03 << t124_thermctl_shifts[zone->sensor];
>> +
>> + val = readl(zone->tegra->regs + THERMCTL_INTR_STATUS);
>> +
>> + if ((val & intr_mask) == 0)
>> + return IRQ_NONE;
>> +
>> + writel(val & intr_mask, zone->tegra->regs + THERMCTL_INTR_STATUS);
> I think we need to disable the interrupt here, and enable it again after
> updating the high/low limited values. If not, there will trigger mass of
> interrupts.
>

Good point. It works now because of-thermal will set up the new trip
points during soctherm_thread_isr, and apparently the interrupt is kept
disabled until after that.

>> +
>> +static struct platform_driver tegra_soctherm_driver = {
>> + .probe = tegra_soctherm_probe,
>> + .remove = tegra_soctherm_remove,
>> + .driver = {
>> + .name = "tegra_soctherm",
>> + .owner = THIS_MODULE,
>> + .of_match_table = tegra_soctherm_of_match,
>> + },
>> +};
> Will you consider to add suspend/resume support?

I guess for this one it should be simple; same driver probe and teardown
as normally. Although currently suspend doesn't support LP0 so no-op is
enough.

>
> Thanks.
> Wei.
>

Thanks


\
 
 \ /
  Last update: 2014-07-04 14:41    [W:0.243 / U:0.368 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site