lkml.org 
[lkml]   [2014]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] ARM: dts: at91-sama5d3_xplained: add the regulator device node
Date


> -----Original Message-----
> From: Ferre, Nicolas
> Sent: Friday, May 09, 2014 11:31 PM
> To: Yang, Wenyou; Alexandre Belloni
> Cc: devicetree@vger.kernel.org; linux-kernel@vger.kernel.org;
> robh+dt@kernel.org; broonie@kernel.org; linux-arm-
> kernel@lists.infradead.org
> Subject: Re: [PATCH] ARM: dts: at91-sama5d3_xplained: add the regulator
> device node
>
> On 22/04/2014 03:37, Yang, Wenyou :
> > Hi,
> >
> >> -----Original Message-----
> >> From: Alexandre Belloni [mailto:alexandre.belloni@free-electrons.com]
> >> Sent: Monday, April 21, 2014 8:22 PM
> >> To: Yang, Wenyou
> >> Cc: devicetree@vger.kernel.org; Ferre, Nicolas; linux-
> >> kernel@vger.kernel.org; robh+dt@kernel.org; broonie@kernel.org;
> >> linux- arm-kernel@lists.infradead.org
> >> Subject: Re: [PATCH] ARM: dts: at91-sama5d3_xplained: add the
> >> regulator device node
> >>
> >> On 21/04/2014 at 11:54:43 +0200, Alexandre Belloni wrote :
> >>> Hi,
> >>>
> >>> On 21/04/2014 at 12:29:07 +0800, Wenyou Yang wrote :
> >>>> +
> >>>> + vddana_reg: LDO_REG2 {
> >>>> + regulator-name =
> "VDDANA";
> >>>> + regulator-min-microvolt
> =
> >> <3300000>;
> >>>> + regulator-max-microvolt
> =
> >> <3300000>;
> >>>> + regulator-always-on;
> >>>
> >>> I'm pretty sure that one is not always on as you actually have to
> >>> configure it to get any voltage. Are you sure you want to set the
> >>> regulator-always-on property here ?
> >>>
> >>
> >> Just to clarify my though, wouldn't it be better to make the ADC
> >> driver handle that regulator instead of using regulator-always-on ?
> > Yes, you are right.
> > It should not use regulator-always-on property for this regulator.
> > It is ADC driver and ISI driver to handle it(The ISI takes PCK for
> clock).
>
> Hi Wenyou and Alexandre,
>
> After talking to our system engineers, it not usual to avoid to power
> the VDDANA rail. In fact it will prevent you to use all the pads that
> are powered by VDDANA: PD20-PD31. Moreover, even if you do not activate
> the ADC output on these lines you won't be able to use them as plain
> GPIO... (Cf. package and pinout section of the datasheet).
>
> As the ADVREF pin of the SoC is connected to the VDDANA on this board
> (even if this default configuration can be modified with a soldering
> iron), we have to note that we may consume a little bit more power.
>
> But still, I would recommend to keep the "regulator-always-on" property
> on this node. Do you agree and allow me to take your first revision of
> the patch?
I agree.

>
>
> Bye,
> --
> Nicolas Ferre

Best Regards,
Wenyou Yang


\
 
 \ /
  Last update: 2014-05-12 07:21    [W:0.044 / U:0.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site