lkml.org 
[lkml]   [2014]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/3] dma: Add Xilinx Video DMA DT Binding Documentation
Date
Device-tree binding documentation of Xilinx Video DMA Engine

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
---
Changes in v3:
None

Changes in v2:
- Removed device-id DT property, as suggested by Arnd Bergmann
- Properly documented DT bindings as suggested by Arnd Bergmann
---
.../devicetree/bindings/dma/xilinx/xilinx_vdma.txt | 75 ++++++++++++++++++++
1 file changed, 75 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt

diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt
new file mode 100644
index 0000000..ab8be1a
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt
@@ -0,0 +1,75 @@
+Xilinx AXI VDMA engine, it does transfers between memory and video devices.
+It can be configured to have one channel or two channels. If configured
+as two channels, one is to transmit to the video device and another is
+to receive from the video device.
+
+Required properties:
+- compatible: Should be "xlnx,axi-vdma-1.00.a"
+- #dma-cells: Should be <1>, see "dmas" property below
+- reg: Should contain VDMA registers location and length.
+- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
+- dma-channel child node: Should have atleast one channel and can have upto
+ two channels per device. This node specifies the properties of each
+ DMA channel (see child node properties below).
+
+Optional properties:
+- xlnx,include-sg: Tells whether configured for Scatter-mode in
+ the hardware.
+- xlnx,flush-fsync: Tells whether which channel to Flush on Frame sync.
+ It takes following values:
+ {1}, flush both channels
+ {2}, flush mm2s channel
+ {3}, flush s2mm channel
+
+Required child node properties:
+- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
+ "xlnx,axi-vdma-s2mm-channel".
+- interrupts: Should contain per channel VDMA interrupts.
+- xlnx,data-width: Should contain the stream data width, take values
+ {32,64...1024}.
+
+Option child node properties:
+- xlnx,include-dre: Tells whether hardware is configured for Data
+ Realignment Engine.
+- xlnx,genlock-mode: Tells whether Genlock synchronization is
+ enabled/disabled in hardware.
+
+Example:
+++++++++
+
+axi_vdma_0: axivdma@40030000 {
+ compatible = "xlnx,axi-vdma-1.00.a";
+ #dma_cells = <1>;
+ reg = < 0x40030000 0x10000 >;
+ xlnx,num-fstores = <0x8>;
+ xlnx,flush-fsync = <0x1>;
+ dma-channel@40030000 {
+ compatible = "xlnx,axi-vdma-mm2s-channel";
+ interrupts = < 0 54 4 >;
+ xlnx,datawidth = <0x40>;
+ } ;
+ dma-channel@40030030 {
+ compatible = "xlnx,axi-vdma-s2mm-channel";
+ interrupts = < 0 53 4 >;
+ xlnx,datawidth = <0x40>;
+ } ;
+} ;
+
+
+* DMA client
+
+Required properties:
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+ where Channel ID is '0' for write/tx and '1' for read/rx
+ channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+ compatible ="xlnx,axi-vdma-test-1.00.a";
+ dmas = <&axi_vdma_0 0
+ &axi_vdma_0 1>;
+ dma-names = "vdma0", "vdma1";
+} ;
--
1.7.9.5


\
 
 \ /
  Last update: 2014-02-15 13:41    [W:0.172 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site