lkml.org 
[lkml]   [2014]   [Feb]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH] mtd: add per NAND partition ECC config
On 10/02/2014 12:55, Gupta, Pekon wrote:
> Hi Boris,
>
>> From: Boris BREZILLON
>>
>> This patch aims to add per partition ECC config for NAND devices.
>> It defines a new field in the mtd struct to store the mtd ECC config and
>> thus each mtd partition device can store its config instead of using the
>> default NAND chip config.
>>
>> This feature is needed to support the sunxi boot0 paritition case:
>> Allwinner boot code (BROM) requires a specific HW ECC for its boot code
>> that may not fit the HW NAND requirements for the entire NAND chip.
>>
>> Signed-off-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
>> ---
>> Hello,
>>
>> This patch is just a draft that implement per partition ECC config.
>> It's currently not properly splitted (it should be separated in several
>> patches) and not documented either.
>>
>> There's at least one point that bother me in the current implementation:
>> I introduced DT notions in the nand core code by the mean of the get_ecc_ctrl
>> callback, and so far this was kept out of mtd/nand core code (I guess it was
>> on purpose).
>>
>> Please let me know if you see other drawbacks.
>>
>> If you think per partition ECC should not be implemented, could you help me
>> find a way to handle sunxi specific case decribed above ?
>>
> There was a discussion on having per partition based ECC earlier [1].
> Though I was not in favor of supporting it earlier, but your proposal looks good.
> However, I still feel there are more caveats here, to explore..
>
> [...]
>
>> @@ -364,7 +367,13 @@ static struct mtd_part *allocate_partition(struct mtd_info *master,
>> slave->mtd.writesize = master->writesize;
>> slave->mtd.writebufsize = master->writebufsize;
>> slave->mtd.oobsize = master->oobsize;
>> - slave->mtd.oobavail = master->oobavail;
>> + if (part->eccctrl) {
>> + slave->mtd.eccctrl = part->eccctrl;
>> + slave->mtd.oobavail = part->eccctrl->layout->oobavail;
>> + } else {
>> + slave->mtd.eccctrl = master->eccctrl;
>> + slave->mtd.oobavail = master->oobavail;
>> + }
>> slave->mtd.subpage_sft = master->subpage_sft;
>>
>> slave->mtd.name = name;
>> @@ -515,9 +524,15 @@ static struct mtd_part *allocate_partition(struct mtd_info *master,
>> part->name);
>> }
>>
>> - slave->mtd.ecclayout = master->ecclayout;
>> - slave->mtd.ecc_step_size = master->ecc_step_size;
>> - slave->mtd.ecc_strength = master->ecc_strength;
>> + if (part->eccctrl) {
>> + slave->mtd.ecclayout = part->eccctrl->layout;
>> + slave->mtd.ecc_step_size = part->eccctrl->size;
>> + slave->mtd.ecc_strength = part->eccctrl->strength;
> You have to replicate 'struct nand_ecc_ctrl' from 'nand_chip' to 'mtd_info'
> because each ECC algorithm may have its own callback for hwctl(), calculate(), and correct().
> How do you plan to populate those ? In driver probe ?

That's already handled (see parse_ofnandpart function):

For each new partition if a valid ecc-mode is detected the function will
call the get_ecc_ctrl
callback which is then supposed to allocate and initialize a new
nand_ecc_ctrl struct.

On nand probe (more precisely in the nand_scan_tail function), I simply
assign the mtd eccctrl
field to the nand chip ecc field, so that even when there's no partition
the mtd device have a
reference to a valid nand_ecc_ctrl struct.

Is that what you were talking about ?

>
>> + } else {
>> + slave->mtd.ecclayout = master->ecclayout;
>> + slave->mtd.ecc_step_size = master->ecc_step_size;
>> + slave->mtd.ecc_strength = master->ecc_strength;
>> + }
>> slave->mtd.bitflip_threshold = master->bitflip_threshold;
>>
>> if (master->_block_isbad) {
> [...]
>
>> +const struct nand_ecc_ctrl *nand_get_ecc_ctrl(struct mtd_info *mtd,
>> + nand_ecc_modes_t mode,
>> + struct device_node *np)
>> +{
>> + struct nand_chip *chip = mtd->priv;
>> + struct nand_ecc_ctrl *ecc;
>> + u32 ecc_step, ecc_strength;
>> + int ret;
>> +
>> + if (mode != NAND_ECC_NONE && mode != NAND_ECC_SOFT &&
>> + mode != NAND_ECC_SOFT_BCH)
>> + return ERR_PTR(-EINVAL);
>> +
>> + ecc = kzalloc(sizeof(*ecc), GFP_KERNEL);
>> + if (!ecc)
>> + return ERR_PTR(-ENOMEM);
>> +
>> + ecc->size = chip->ecc_step_ds;
>> + ecc->strength = chip->ecc_strength_ds;
>> + if (!of_get_nand_ecc_level(np, &ecc_strength, &ecc_step)) {
>> + ecc->size = ecc_step;
>> + ecc->strength = ecc_strength;
>> + }
>> +
> Here we may need to ecc_strength for each partition.
> Example: for OMAP3 ROM supports only HAM1 (1-bit hamming),
> but kernel may support up-to BCH8 (8-bit BCH) ECC schemes.
> But, anyways that's specific to OMAP platforms..

If you need HW specific handling, you just have to implement a new
get_ecc_ctrl
function and assign it to the get_ecc_ctrl field before calling
nand_scan_tail.
That's what I'm doing in the sunxi driver.

This nand_get_ecc_ctrl function is only used when no specific
get_ecc_ctrl is provided.


>> + switch (mode) {
>> + case NAND_ECC_NONE:
>> + break;
>> + case NAND_ECC_SOFT:
>> + break;
>> + case NAND_ECC_SOFT_BCH:
>> + ecc->bytes = ((ecc->strength * fls(8 * ecc->size)) + 7) / 8;
>> + break;
>> + default:
>> + ret = -EINVAL;
>> + goto err;
>> + }
>> +
>> + ecc->mode = mode;
>> + ret = nand_ecc_ctrl_init(mtd, ecc);
>> + if (ret)
>> + goto err;
>> +
>> + ecc->release = nand_release_ecc_ctrl;
>> +
>> + return ecc;
>> +
>> +err:
>> + kfree(ecc);
>> + return ERR_PTR(ret);
>> +}
>> +EXPORT_SYMBOL(nand_get_ecc_ctrl);
>> +
> I'll be happy to extend and test this, if you plan a complete version.

This version is fully functionnal (I tested it with the sunxi driver),
but it depends on a this
patch: https://lkml.org/lkml/2014/1/29/210.

I'll be happy to get it tested on other platforms.

Best Regards,

Boris

>
> [1] http://comments.gmane.org/gmane.linux.ports.arm.omap/108083
> (you can skip initial discussion about OMAP3, and jump to Thomas Petazzoni | 2 Dec 17:19 2013)
>
>
> with regards, pekon



\
 
 \ /
  Last update: 2014-02-10 14:01    [W:0.359 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site