lkml.org 
[lkml]   [2014]   [Nov]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH V4] arm64: amd-seattle: Adding device tree for AMD Seattle platform
On Tue, Nov 25, 2014 at 11:46:50AM +0000, Suthikulpanit, Suravee wrote:
> Hi Marc,
>
> On 11/25/14, 17:23, "Marc Zyngier" <marc.zyngier@arm.com> wrote:
>
> >Hi Suravee,
> >
> >Just spotted a small issue below (looks like a recurring mistake in a
> >number of DTs I've seem lately):
> >
> >On 24/11/14 21:51, suravee.suthikulpanit@amd.com wrote:
> >> From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
> >>
> >> Initial revision of device tree for AMD Seattle platform.
> >>
> >> Cc: Arnd Bergmann <arnd@arndb.de>
> >> Cc: Marc Zyngier <marc.zyngier@arm.com>
> >> Cc: Mark Rutland <mark.rutland@arm.com>
> >> Cc: Will Deacon <will.deacon@arm.com>
> >> Cc: Catalin Marinas <catalin.marinas@arm.com>
> >> Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
> >> Signed-off-by: Thomas Lendacky <Thomas.Lendacky@amd.com>
> >> Signed-off-by: Joel Schopp <Joel.Schopp@amd.com>
> >> ---
> >> V4 Changes:
> >> * Remove unnecessary smb layer and move motherbord to top level
> >> * Move include dtsi to top level
> >> * Remove apb_pclk from sata0 and i2c
> >> * Fix GIC Virtual Maintanance Interrupt from PPI24 (8) to PPI25 (9)
> >> * Add 40-bit dma-ranges for motherboard (simple-bus)
> >> * Remove dma0 (pl330) entry for now since it only supports 32-bit
> >>DMA.
> >> It is basically not used at the moment. It would also need SMMU
> >> to allow dma remapping to 40-bit DMA range.
> >> * Add phandle spi0 and spi1
> >> * Hook up gpio0 pin 7 with MMC Card Detection (CD) support.
> >> * Changes in pcie0 entry:
> >> - Add 40-bit dma-ranges
> >> - Remove interrupts property
> >> - Add interrupt-map/mask property
> >> - Fix PCI I/O range
> >> - Merge PCI 32-bit ranges
> >> - Merge PCI 64-bit ranges
> >>
> >> NOTE: I am not add a new compatible ID for the sata0 as Rob Herring
> >> suggested since there is no need at the momement, and I am trying
> >> to avoid introducing ID unnecessarily.
> >>
> >> arch/arm64/Kconfig | 5 +
> >> arch/arm64/boot/dts/Makefile | 1 +
> >> arch/arm64/boot/dts/amd-seattle-periph.dtsi | 156
> >>++++++++++++++++++++++++++++
> >> arch/arm64/boot/dts/amd-seattle.dts | 89 ++++++++++++++++
> >> 4 files changed, 251 insertions(+)
> >> create mode 100644 arch/arm64/boot/dts/amd-seattle-periph.dtsi
> >> create mode 100644 arch/arm64/boot/dts/amd-seattle.dts
> >>
> >
> >[...]
> >
> >> diff --git a/arch/arm64/boot/dts/amd-seattle.dts
> >>b/arch/arm64/boot/dts/amd-seattle.dts
> >> new file mode 100644
> >> index 0000000..d5fc482
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/amd-seattle.dts
> >> @@ -0,0 +1,89 @@
> >> +/*
> >> + * DTS file for AMD Seattle
> >> + *
> >> + * Copyright (C) 2014 Advanced Micro Devices, Inc.
> >> + */
> >> +
> >> +/dts-v1/;
> >> +
> [...]
>
> >> +
> >> + timer {
> >> + compatible = "arm,armv8-timer";
> >> + interrupts = <1 13 0xff01>,
> >> + <1 14 0xff01>,
> >> + <1 11 0xff01>,
> >> + <1 10 0xff01>;
> >> + };
> >
> >The Cortex-A57 TRM clearly states that these interrupts are level
> >triggered.
>
> Thanks for pointing this out. I¹ll fix this to <1 1X 0xff04> (4 for the
> Active-High) then.

Hi Suravee,

Don't know what Seattle does, but the TRM says that the outputs are active-LOW.

Best regards,
Liviu

>
> Suravee
>
> >
>
>

--
====================
| I would like to |
| fix the world, |
| but they're not |
| giving me the |
\ source code! /
---------------
¯\_(ツ)_/¯


\
 
 \ /
  Last update: 2014-11-27 16:01    [W:0.084 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site