lkml.org 
[lkml]   [2014]   [Oct]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3] iio: iadc: Qualcomm SPMI PMIC current ADC driver
On 01/10/14 17:14, Ivan T. Ivanov wrote:
> The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> 16 bits resolution and register space inside PMIC accessible across
> SPMI bus.
>
> The driver registers itself through IIO interface.
>
> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Looks good to me. I would however like to wait for Mark Rutland to
say whether he is happy with the bindings (and the rest if he
feels like it ;)

Given the merge window will open shortly and hence the IIO merge
window is long closed, we aren't in a particular rush at the moment.


Jonathan

> ---
>
> Changes since v2:
>
> - DT bindings fixed according comments.
> - IADC driver now register 2 channels instead of just one.
> - Fixed sense resistor Ohms dimensions. It is supposed that
> values are around 0.010 Ohms not 10 Mega Ohms.
> - Removed direct driver access to registers in Battery Monitor
> peripheral address space. Which will impact correct internal
> sense resistor calculation on some variants and vendors of
> pm8110 and pm8226. This could be added once we figured out how
> to pass/read PMIC device version from sub-function drivers.
>
> v2: http://www.gossamer-threads.com/lists/linux/kernel/2016613
>
> .../devicetree/bindings/iio/adc/qcom,spmi-iadc.txt | 46 ++
> drivers/iio/adc/Kconfig | 11 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/qcom-spmi-iadc.c | 626 +++++++++++++++++++++
> 4 files changed, 684 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt
> create mode 100644 drivers/iio/adc/qcom-spmi-iadc.c
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt
> new file mode 100644
> index 0000000..833afd6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-iadc.txt
> @@ -0,0 +1,46 @@
> +Qualcomm's SPMI PMIC current ADC
> +
> +QPNP PMIC current ADC (IADC) provides interface to clients to read current.
> +A 16 bit ADC is used for current measurements. IADC can measure the current
> +through an external resistor(channel 1)or internal(built-in) resistor
> +(channel 0). When using an external resistor it is to be described by
> +qcom,external-resistor-micro-ohms property.
> +
> +IADC node:
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: Should contain "qcom,spmi-iadc".
> +
> +- reg:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: IADC base address and length in the SPMI PMIC register map
> +
> +- interrupts:
> + Usage: optional
> + Value type: <prop-encoded-array>
> + Definition: End of ADC conversion.
> +
> +- qcom,external-resistor-micro-ohms:
> + Usage: optional
> + Value type: <u32>
> + Definition: Sense resister value in micro Ohm.
> + If not defined value of 10000 micro Ohms will be used.
> +
> +Example:
> + /* IADC node */
> + pmic_iadc: iadc@3600 {
> + compatible = "qcom,spmi-iadc";
> + reg = <0x3600 0x100>;
> + interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
> + qcom,external-resistor-micro-ohms = <10000>;
> + #io-channel-cells = <1>;
> + };
> +
> + /* IIO client node */
> + bat {
> + io-channels = <&pmic_iadc>;
> + io-channel-names = "iadc 0";
> + };
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 11b048a..ee1ad5b 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -206,6 +206,17 @@ config NAU7802
> To compile this driver as a module, choose M here: the
> module will be called nau7802.
>
> +config QCOM_SPMI_IADC
> + tristate "Qualcomm SPMI PMIC current ADC"
> + depends on SPMI
> + select REGMAP_SPMI
> + help
> + This is the IIO Current ADC driver for Qualcomm QPNP IADC Chip.
> +
> + The driver supports single mode operation to read from two
> + channels (external or internal). Hardware have additional
> + channels internally used for gain and offset calibration.
> +
> config TI_ADC081C
> tristate "Texas Instruments ADC081C021/027"
> depends on I2C
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index ad81b51..c790543 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -30,3 +30,4 @@ obj-$(CONFIG_VF610_ADC) += vf610_adc.o
> obj-$(CONFIG_VIPERBOARD_ADC) += viperboard_adc.o
> xilinx-xadc-y := xilinx-xadc-core.o xilinx-xadc-events.o
> obj-$(CONFIG_XILINX_XADC) += xilinx-xadc.o
> +obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
> diff --git a/drivers/iio/adc/qcom-spmi-iadc.c b/drivers/iio/adc/qcom-spmi-iadc.c
> new file mode 100644
> index 0000000..f4328f2
> --- /dev/null
> +++ b/drivers/iio/adc/qcom-spmi-iadc.c
> @@ -0,0 +1,626 @@
> +/*
> + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mutex.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +/* IADC register and bit definition */
> +#define IADC_REVISION2 0x1
> +#define IADC_REVISION2_SUPPORTED_IADC 1
> +
> +#define IADC_PERPH_TYPE 0x4
> +#define IADC_PERPH_TYPE_ADC 8
> +
> +#define IADC_PERPH_SUBTYPE 0x5
> +#define IADC_PERPH_SUBTYPE_IADC 3
> +
> +#define IADC_STATUS1 0x8
> +#define IADC_STATUS1_OP_MODE 4
> +#define IADC_STATUS1_REQ_STS BIT(1)
> +#define IADC_STATUS1_EOC BIT(0)
> +#define IADC_STATUS1_REQ_STS_EOC_MASK 0x3
> +
> +#define IADC_MODE_CTL 0x40
> +#define IADC_OP_MODE_SHIFT 3
> +#define IADC_OP_MODE_NORMAL 0
> +#define IADC_TRIM_EN BIT(0)
> +
> +#define IADC_EN_CTL1 0x46
> +#define IADC_EN_CTL1_SET BIT(7)
> +
> +#define IADC_CH_SEL_CTL 0x48
> +
> +#define IADC_DIG_PARAM 0x50
> +#define IADC_DIG_DEC_RATIO_SEL_SHIFT 2
> +
> +#define IADC_HW_SETTLE_DELAY 0x51
> +
> +#define IADC_CONV_REQ 0x52
> +#define IADC_CONV_REQ_SET BIT(7)
> +
> +#define IADC_FAST_AVG_CTL 0x5a
> +#define IADC_FAST_AVG_EN 0x5b
> +#define IADC_FAST_AVG_EN_SET BIT(7)
> +
> +#define IADC_PERH_RESET_CTL3 0xda
> +#define IADC_FOLLOW_WARM_RB BIT(2)
> +
> +#define IADC_DATA0 0x60
> +#define IADC_DATA1 0x61
> +
> +#define IADC_SEC_ACCESS 0xd0
> +#define IADC_SEC_ACCESS_DATA 0xa5
> +
> +#define IADC_NOMINAL_RSENSE 0xf4
> +#define IADC_NOMINAL_RSENSE_SIGN_MASK BIT(7)
> +
> +#define IADC_REF_GAIN_MICRO_VOLTS 17857
> +
> +#define IADC_INT_RSENSE_DEVIATION 15625 /* nano Ohms per bit */
> +
> +#define IADC_INT_RSENSE_IDEAL_VALUE 10000 /* micro Ohms */
> +#define IADC_INT_RSENSE_DEFAULT_VALUE 7800 /* micro Ohms */
> +#define IADC_INT_RSENSE_DEFAULT_GF 9000 /* micro Ohms */
> +#define IADC_INT_RSENSE_DEFAULT_SMIC 9700 /* micro Ohms */
> +
> +#define IADC_CONV_TIME_MIN_US 2000
> +#define IADC_CONV_TIME_MAX_US 2100
> +
> +#define IADC_DEF_PRESCALING 0 /* 1:1 */
> +#define IADC_DEF_DECIMATION 0 /* 512 */
> +#define IADC_DEF_HW_SETTLE_TIME 0 /* 0 us */
> +#define IADC_DEF_AVG_SAMPLES 0 /* 1 sample */
> +
> +/* IADC channel list */
> +#define IADC_INT_RSENSE 0
> +#define IADC_EXT_RSENSE 1
> +#define IADC_GAIN_17P857MV 3
> +#define IADC_EXT_OFFSET_CSP_CSN 5
> +#define IADC_INT_OFFSET_CSP2_CSN2 6
> +
> +/**
> + * struct iadc_drv - IADC Current ADC device structure.
> + * @regmap: regmap for register read/write.
> + * @dev: This device pointer.
> + * @base: base offset for the ADC peripheral.
> + * @rsense: Values of the internal and external sense resister in micro Ohms.
> + * @poll_eoc: Poll for end of conversion instead of waiting for IRQ.
> + * @offset_raw: Raw offset values for the internal and external channels.
> + * @gain_raw: Raw gain of the channels.
> + * @lock: ADC lock for access to the peripheral.
> + * @complete: ADC notification after end of conversion interrupt is received.
> + */
> +struct iadc_chip {
> + struct regmap *regmap;
> + struct device *dev;
> + u16 base;
> + bool poll_eoc;
> + int rsense[2];
> + u16 offset_raw[2];
> + u16 gain_raw;
> + struct mutex lock;
> + struct completion complete;
> +};
> +
> +static int iadc_read(struct iadc_chip *iadc, u16 offset, u8 *data)
> +{
> + unsigned int val;
> + int ret;
> +
> + ret = regmap_read(iadc->regmap, iadc->base + offset, &val);
> + if (ret < 0)
> + return ret;
> +
> + *data = val;
> + return 0;
> +}
> +
> +static int iadc_write(struct iadc_chip *iadc, u16 offset, u8 data)
> +{
> + return regmap_write(iadc->regmap, iadc->base + offset, data);
> +}
> +
> +static int iadc_reset(struct iadc_chip *iadc)
> +{
> + u8 data;
> + int ret;
> +
> + ret = iadc_write(iadc, IADC_SEC_ACCESS, IADC_SEC_ACCESS_DATA);
> + if (ret < 0)
> + return ret;
> +
> + ret = iadc_read(iadc, IADC_PERH_RESET_CTL3, &data);
> + if (ret < 0)
> + return ret;
> +
> + ret = iadc_write(iadc, IADC_SEC_ACCESS, IADC_SEC_ACCESS_DATA);
> + if (ret < 0)
> + return ret;
> +
> + data |= IADC_FOLLOW_WARM_RB;
> +
> + return iadc_write(iadc, IADC_PERH_RESET_CTL3, data);
> +}
> +
> +static int iadc_set_state(struct iadc_chip *iadc, bool state)
> +{
> + u8 data = 0;
> +
> + if (state)
> + data = IADC_EN_CTL1_SET;
> +
> + return iadc_write(iadc, IADC_EN_CTL1, data);
> +}
> +
> +static void iadc_status_show(struct iadc_chip *iadc)
> +{
> + u8 mode, sta1, chan, dig, en, req;
> + int ret;
> +
> + ret = iadc_read(iadc, IADC_MODE_CTL, &mode);
> + if (ret < 0)
> + return;
> +
> + ret = iadc_read(iadc, IADC_DIG_PARAM, &dig);
> + if (ret < 0)
> + return;
> +
> + ret = iadc_read(iadc, IADC_CH_SEL_CTL, &chan);
> + if (ret < 0)
> + return;
> +
> + ret = iadc_read(iadc, IADC_CONV_REQ, &req);
> + if (ret < 0)
> + return;
> +
> + ret = iadc_read(iadc, IADC_STATUS1, &sta1);
> + if (ret < 0)
> + return;
> +
> + ret = iadc_read(iadc, IADC_EN_CTL1, &en);
> + if (ret < 0)
> + return;
> +
> + dev_err(iadc->dev,
> + "mode:%02x en:%02x chan:%02x dig:%02x req:%02x sta1:%02x\n",
> + mode, en, chan, dig, req, sta1);
> +}
> +
> +static int iadc_configure(struct iadc_chip *iadc, int channel)
> +{
> + u8 decim, mode;
> + int ret;
> +
> + /* Mode selection */
> + mode = (IADC_OP_MODE_NORMAL << IADC_OP_MODE_SHIFT) | IADC_TRIM_EN;
> + ret = iadc_write(iadc, IADC_MODE_CTL, mode);
> + if (ret < 0)
> + return ret;
> +
> + /* Channel selection */
> + ret = iadc_write(iadc, IADC_CH_SEL_CTL, channel);
> + if (ret < 0)
> + return ret;
> +
> + /* Digital parameter setup */
> + decim = IADC_DEF_DECIMATION << IADC_DIG_DEC_RATIO_SEL_SHIFT;
> + ret = iadc_write(iadc, IADC_DIG_PARAM, decim);
> + if (ret < 0)
> + return ret;
> +
> + /* HW settle time delay */
> + ret = iadc_write(iadc, IADC_HW_SETTLE_DELAY, IADC_DEF_HW_SETTLE_TIME);
> + if (ret < 0)
> + return ret;
> +
> + ret = iadc_write(iadc, IADC_FAST_AVG_CTL, IADC_DEF_AVG_SAMPLES);
> + if (ret < 0)
> + return ret;
> +
> + if (IADC_DEF_AVG_SAMPLES)
> + ret = iadc_write(iadc, IADC_FAST_AVG_EN, IADC_FAST_AVG_EN_SET);
> + else
> + ret = iadc_write(iadc, IADC_FAST_AVG_EN, 0);
> +
> + if (ret < 0)
> + return ret;
> +
> + if (!iadc->poll_eoc)
> + reinit_completion(&iadc->complete);
> +
> + ret = iadc_set_state(iadc, true);
> + if (ret < 0)
> + return ret;
> +
> + /* Request conversion */
> + return iadc_write(iadc, IADC_CONV_REQ, IADC_CONV_REQ_SET);
> +}
> +
> +static int iadc_poll_wait_eoc(struct iadc_chip *iadc, int interval_us)
> +{
> + int ret, count, retry;
> + u8 sta1;
> +
> + retry = interval_us / IADC_CONV_TIME_MIN_US;
> +
> + for (count = 0; count < retry; count++) {
> + ret = iadc_read(iadc, IADC_STATUS1, &sta1);
> + if (ret < 0)
> + return ret;
> +
> + sta1 &= IADC_STATUS1_REQ_STS_EOC_MASK;
> + if (sta1 == IADC_STATUS1_EOC)
> + return 0;
> +
> + usleep_range(IADC_CONV_TIME_MIN_US, IADC_CONV_TIME_MAX_US);
> + }
> +
> + iadc_status_show(iadc);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int iadc_read_result(struct iadc_chip *iadc, u16 *data)
> +{
> + u8 lsb, msb;
> + int ret;
> +
> + ret = iadc_read(iadc, IADC_DATA0, &lsb);
> + if (ret < 0)
> + return ret;
> +
> + ret = iadc_read(iadc, IADC_DATA1, &msb);
> + if (ret < 0)
> + return ret;
> +
> + *data = (msb << 8) | lsb;
> +
> + return 0;
> +}
> +
> +static int iadc_do_conversion(struct iadc_chip *iadc, int chan, u16 *data)
> +{
> + int wait, ret;
> +
> + ret = iadc_configure(iadc, chan);
> + if (ret < 0)
> + goto exit;
> +
> + wait = BIT(IADC_DEF_AVG_SAMPLES) * IADC_CONV_TIME_MIN_US * 2;
> +
> + if (iadc->poll_eoc) {
> + ret = iadc_poll_wait_eoc(iadc, wait);
> + } else {
> + ret = wait_for_completion_timeout(&iadc->complete, wait);
> + if (!ret)
> + ret = -ETIMEDOUT;
> + else
> + /* double check conversion status */
> + ret = iadc_poll_wait_eoc(iadc, IADC_CONV_TIME_MIN_US);
> + }
> +
> + if (!ret)
> + ret = iadc_read_result(iadc, data);
> +exit:
> + iadc_set_state(iadc, false);
> + if (ret < 0)
> + dev_err(iadc->dev, "conversion failed\n");
> +
> + return ret;
> +}
> +
> +static int iadc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct iadc_chip *iadc = iio_priv(indio_dev);
> + long isense_ua, vsense_uv, vsense_raw;
> + int ret, sign;
> + u16 adc_raw;
> +
> + mutex_lock(&iadc->lock);
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + ret = iadc_do_conversion(iadc, chan->channel, &adc_raw);
> + if (ret < 0)
> + goto exit;
> +
> + vsense_raw = adc_raw - iadc->offset_raw[chan->channel];
> +
> + vsense_uv = vsense_raw * IADC_REF_GAIN_MICRO_VOLTS;
> + vsense_uv /= iadc->gain_raw - iadc->offset_raw[chan->channel];
> +
> + sign = 1;
> + if (vsense_uv < 0)
> + sign = -1;
> +
> + isense_ua = sign * vsense_uv;
> +
> + do_div(isense_ua, iadc->rsense[chan->channel]);
> +
> + isense_ua = sign * isense_ua;
> +
> + dev_dbg(iadc->dev, "offset %d, gain %d, adc %d, V=%ld,uV, I=%ld,uA\n",
> + iadc->offset_raw[chan->channel], iadc->gain_raw,
> + adc_raw, vsense_uv, isense_ua);
> +
> + *val = isense_ua;
> + ret = IIO_VAL_INT;
> + break;
> + case IIO_CHAN_INFO_SCALE:
> + *val = 0;
> + *val2 = 1000;
> + ret = IIO_VAL_INT_PLUS_MICRO;
> + break;
> + default:
> + ret = -EINVAL;
> + break;
> + }
> +
> +exit:
> + mutex_unlock(&iadc->lock);
> +
> + return ret;
> +}
> +
> +static const struct iio_info iadc_info = {
> + .read_raw = iadc_read_raw,
> + .driver_module = THIS_MODULE,
> +};
> +
> +static irqreturn_t iadc_isr(int irq, void *dev_id)
> +{
> + struct iadc_chip *iadc = dev_id;
> +
> + complete(&iadc->complete);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int iadc_update_offset(struct iadc_chip *iadc)
> +{
> + int ret;
> +
> + ret = iadc_do_conversion(iadc, IADC_GAIN_17P857MV, &iadc->gain_raw);
> + if (ret < 0)
> + return ret;
> +
> + ret = iadc_do_conversion(iadc, IADC_INT_OFFSET_CSP2_CSN2,
> + &iadc->offset_raw[IADC_INT_RSENSE]);
> + if (ret < 0)
> + return ret;
> +
> + if ((iadc->gain_raw - iadc->offset_raw[IADC_INT_RSENSE]) == 0) {
> + dev_err(iadc->dev, "error: internal offset %d gain %d\n",
> + iadc->offset_raw[IADC_INT_RSENSE], iadc->gain_raw);
> + return -EINVAL;
> + }
> +
> + ret = iadc_do_conversion(iadc, IADC_EXT_OFFSET_CSP_CSN,
> + &iadc->offset_raw[IADC_EXT_RSENSE]);
> + if (ret < 0)
> + return ret;
> +
> + if ((iadc->gain_raw - iadc->offset_raw[IADC_EXT_RSENSE]) == 0) {
> + dev_err(iadc->dev, "error: external offset %d gain %d\n",
> + iadc->offset_raw[IADC_EXT_RSENSE], iadc->gain_raw);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int iadc_version_check(struct iadc_chip *iadc)
> +{
> + u8 revision, type, subtype;
> + int ret;
> +
> + ret = iadc_read(iadc, IADC_PERPH_TYPE, &type);
> + if (ret < 0)
> + return ret;
> +
> + if (type < IADC_PERPH_TYPE_ADC) {
> + dev_err(iadc->dev, "%d is not ADC\n", type);
> + return -EINVAL;
> + }
> +
> + ret = iadc_read(iadc, IADC_PERPH_SUBTYPE, &subtype);
> + if (ret < 0)
> + return ret;
> +
> + if (subtype < IADC_PERPH_SUBTYPE_IADC) {
> + dev_err(iadc->dev, "%d is not IADC\n", subtype);
> + return -EINVAL;
> + }
> +
> + ret = iadc_read(iadc, IADC_REVISION2, &revision);
> + if (ret < 0)
> + return ret;
> +
> + if (revision < IADC_REVISION2_SUPPORTED_IADC) {
> + dev_err(iadc->dev, "revision %d not supported\n", revision);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int iadc_rsense_read(struct iadc_chip *iadc, struct device_node *node)
> +{
> + int ret, sign, int_sense;
> + u8 deviation;
> +
> + ret = of_property_read_u32(node, "qcom,external-resistor-micro-ohms",
> + &iadc->rsense[IADC_EXT_RSENSE]);
> + if (ret < 0)
> + iadc->rsense[IADC_EXT_RSENSE] = IADC_INT_RSENSE_IDEAL_VALUE;
> +
> + if (!iadc->rsense[IADC_EXT_RSENSE]) {
> + dev_err(iadc->dev, "qcom,external-resistor-micro-ohms can't be 0");
> + return -EINVAL;
> + }
> +
> + ret = iadc_read(iadc, IADC_NOMINAL_RSENSE, &deviation);
> + if (ret < 0)
> + return ret;
> +
> + sign = 1;
> + if (deviation & IADC_NOMINAL_RSENSE_SIGN_MASK)
> + sign = -1;
> +
> + deviation &= ~IADC_NOMINAL_RSENSE_SIGN_MASK;
> +
> + int_sense = IADC_INT_RSENSE_IDEAL_VALUE * 1000;
> + int_sense += sign * deviation * IADC_INT_RSENSE_DEVIATION;
> + int_sense /= 1000; /* micro Ohms */
> +
> + iadc->rsense[IADC_INT_RSENSE] = int_sense;
> +
> + return 0;
> +}
> +
> +static const struct iio_chan_spec iadc_channels[] = {
> + {
> + .type = IIO_CURRENT,
> + .datasheet_name = "INTERNAL_RSENSE",
> + .channel = 0,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_SCALE),
> + .indexed = 1,
> + },
> + {
> + .type = IIO_CURRENT,
> + .datasheet_name = "EXTERNAL_RSENSE",
> + .channel = 1,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_SCALE),
> + .indexed = 1,
> + },
> +};
> +
> +static int iadc_probe(struct platform_device *pdev)
> +{
> + struct device_node *node = pdev->dev.of_node;
> + struct device *dev = &pdev->dev;
> + struct iio_dev *indio_dev;
> + struct iadc_chip *iadc;
> + int ret, irq_eoc, res[2];
> +
> + indio_dev = devm_iio_device_alloc(dev, sizeof(*iadc));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + iadc = iio_priv(indio_dev);
> + iadc->dev = dev;
> +
> + iadc->regmap = dev_get_regmap(dev->parent, NULL);
> + if (!iadc->regmap)
> + return -ENODEV;
> +
> + init_completion(&iadc->complete);
> + mutex_init(&iadc->lock);
> +
> + platform_set_drvdata(pdev, iadc);
> +
> + ret = of_property_read_u32_array(node, "reg", res, 2);
> + if (ret < 0)
> + return -ENODEV;
> +
> + iadc->base = res[0];
> +
> + ret = iadc_version_check(iadc);
> + if (ret < 0)
> + return -ENODEV;
> +
> + ret = iadc_rsense_read(iadc, node);
> + if (ret < 0)
> + return -ENODEV;
> +
> + dev_dbg(iadc->dev, "sense resistors %d and %d micro Ohm\n",
> + iadc->rsense[IADC_INT_RSENSE],
> + iadc->rsense[IADC_EXT_RSENSE]);
> +
> + irq_eoc = platform_get_irq(pdev, 0);
> + if (irq_eoc == -EPROBE_DEFER)
> + return irq_eoc;
> +
> + if (irq_eoc < 0)
> + iadc->poll_eoc = true;
> +
> + ret = iadc_reset(iadc);
> + if (ret < 0) {
> + dev_err(dev, "reset failed\n");
> + return ret;
> + }
> +
> + if (!iadc->poll_eoc) {
> + ret = devm_request_irq(dev, irq_eoc, iadc_isr, 0,
> + "spmi-iadc", iadc);
> + if (!ret)
> + enable_irq_wake(irq_eoc);
> + else
> + return ret;
> + } else {
> + device_init_wakeup(iadc->dev, 1);
> + }
> +
> + ret = iadc_update_offset(iadc);
> + if (ret < 0) {
> + dev_err(dev, "failed offset calibration\n");
> + return ret;
> + }
> +
> + indio_dev->dev.parent = dev;
> + indio_dev->dev.of_node = node;
> + indio_dev->name = pdev->name;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &iadc_info;
> + indio_dev->channels = iadc_channels;
> + indio_dev->num_channels = ARRAY_SIZE(iadc_channels);
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
> +
> +static const struct of_device_id iadc_match_table[] = {
> + { .compatible = "qcom,spmi-iadc" },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(of, iadc_match_table);
> +
> +static struct platform_driver iadc_driver = {
> + .driver = {
> + .name = "spmi-iadc",
> + .of_match_table = iadc_match_table,
> + },
> + .probe = iadc_probe,
> +};
> +
> +module_platform_driver(iadc_driver);
> +
> +MODULE_ALIAS("platform:spmi-iadc");
> +MODULE_DESCRIPTION("Qualcomm SPMI PMIC current ADC driver");
> +MODULE_LICENSE("GPL v2");
>


\
 
 \ /
  Last update: 2014-10-04 14:41    [W:0.103 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site