lkml.org 
[lkml]   [2014]   [Oct]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/4] arm: boot: dts: am335x-evm: Make charge delay a DT parameter for tsc
Vignesh R schrieb am 27.10.2014 12:08:
> The charge delay value is by default 0xB000. But it can be set to lower
> values on some boards as long as false pen-ups are avoided. Lowering the
> value increases the sampling rate (though current sampling rate is
> sufficient for tsc operation). Hence charge delay has been made a DT
> parameter.
>
I would recommend to use a few colons to separate some thoughts. Also, limit to 80 chars per line would be beneficial. See inline.
> Signed-off-by: Vignesh R <vigneshr@ti.com>
> ---
> .../devicetree/bindings/input/touchscreen/ti-tsc-adc.txt | 13 +++++++++++++
> arch/arm/boot/dts/am335x-evm.dts | 1 +
> 2 files changed, 14 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> index 878549ba814d..ac62769e70e4 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> @@ -28,6 +28,18 @@ Required properties:
> ti,adc-channels: List of analog inputs available for ADC.
> AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
>
> +Optional properties:
> +- child "tsc"
> + ti,charge-delay: Length of touch screen charge delay step in terms of
> + ADC clock cycles. Charge delay value should be large in order
> + to avoid false pen-up events. This value affects the overall
> + sampling speed hence need to be kept as low as possible while
<...> speed, hence needs to be <...>
> + avoiding false pen-up event. Start from a lower value say 0x400
<...> pen-up events. Start from a lower value, like 0x400, and increase <...>
> + and increase value until false pen-up events are avoided. The
> + pen-up detection happens immediately after the charge step
<...> charge step, so this <...>
> + so this does in fact function as a hardware knob for adjusting
> + the amount of "settling time".
> +
> Example:
> tscadc: tscadc@44e0d000 {
> compatible = "ti,am3359-tscadc";
> @@ -36,6 +48,7 @@ Example:
> ti,x-plate-resistance = <200>;
> ti,coordiante-readouts = <5>;
> ti,wire-config = <0x00 0x11 0x22 0x33>;
> + ti,charge-delay = <0xB000>;
> };
>
> adc {
> diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
> index e2156a583de7..80be0462298b 100644
> --- a/arch/arm/boot/dts/am335x-evm.dts
> +++ b/arch/arm/boot/dts/am335x-evm.dts
> @@ -641,6 +641,7 @@
> ti,x-plate-resistance = <200>;
> ti,coordinate-readouts = <5>;
> ti,wire-config = <0x00 0x11 0x22 0x33>;
> + ti,charge-delay = <0xB000>;
> };
>
> adc {
>



\
 
 \ /
  Last update: 2014-10-31 22:21    [W:0.188 / U:0.664 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site