lkml.org 
[lkml]   [2014]   [Oct]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/4] gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
On Wed, Oct 29, 2014 at 10:41:19AM +0100, Linus Walleij wrote:
> On Fri, Oct 24, 2014 at 2:16 PM, Mika Westerberg
> <mika.westerberg@linux.intel.com> wrote:
>
> > The GPIO resources (GpioIo/GpioInt) used in ACPI contain a GPIO number
> > which is relative to the hardware GPIO controller. Typically this number
> > can be translated directly to Linux GPIO number because the mapping is
> > pretty much 1:1.
> >
> > However, when the GPIO driver is using pins exported by a pin controller
> > driver via set of GPIO ranges, the mapping might not be 1:1 anymore and
> > direct translation does not work.
> >
> > In such cases we need to translate the ACPI GPIO number to be suitable for
> > the GPIO controller driver in question by checking all the pin controller
> > GPIO ranges under the given device and using those to get the proper GPIO
> > number.
> >
> > Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
>
> I'm not sure what this patch does so I try to rely on you guys here.
> I would strongly like to have Rafael's ACK before proceeding.
>
> Trying to get the GPIO offsets to map 1:1 to Linux GPIO numbers
> is something that should be avoided since we want to get rid of the
> GPIO number space altogether. GPIO chips should try to register
> with .base = -1 so that the gpiolib just assigns some random GPIO
> numbers to the lines.
>
> What does actually exist?
>
> - GPIO offsets for a certain gpio_chip 0..N
> - Pin offsets for a certain pin controller 0..N
>
> GPIO ranges are for translating between these two.
>
> But I have a vague idea that there is something like a numberspace
> concept inside ACPI as well, and that is all magic to me...
> mixing that into this is a bit scary to me.

Let me try to explain.

As an example, we have touch panel that has GPIO interrupt declared in
ACPI like this:

GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{ // Pin list
76
}

The number 76 in this case is GPIO controller relative GPIO number.

Now, we have pinctrl-cherryview.c which has gaps in the pin space (some
of the pins are not available to the OS at all). So for this particular
pin we have:

# grep SATA_GP1 pins
pin 76 (SATA_GP1) mode 1 ctrl0 0x00010200 ctrl1 0x04c00000

# cat gpio-ranges
GPIO ranges handled:
0: INT33FF:00 GPIOS [456 - 463] PINS [0 - 7]
8: INT33FF:00 GPIOS [464 - 471] PINS [15 - 22]
16: INT33FF:00 GPIOS [472 - 479] PINS [30 - 37]
24: INT33FF:00 GPIOS [480 - 487] PINS [45 - 52]
32: INT33FF:00 GPIOS [488 - 495] PINS [60 - 67]
40: INT33FF:00 GPIOS [496 - 503] PINS [75 - 82]
48: INT33FF:00 GPIOS [504 - 511] PINS [90 - 97]

In other words GPIO number for pin 76 is 496 (in Linux global number
space) and 41 in the GPIO driver local number space.

In order to translate the ACPI GPIO number 76 to the right GPIO number
we iterate over each range in the GPIO driver and look for the match.
Note that it actually uses the local number (41) here:

...
offset = acpi_gpiochip_pin_to_gpio_offset(chip, pin);
if (offset < 0)
return ERR_PTR(offset);

return gpiochip_get_desc(chip, (u16)offset);

However, if you or others have better ideas how to do this I'm all ears
:-)

> > +#ifdef CONFIG_PINCTRL
> > +/**
> > + * acpi_gpiochip_pin_to_gpio_offset() - translates ACPI GPIO to Linux GPIO
> > + * @chip: GPIO chip
> > + * @pin: ACPI GPIO pin number from GpioIo/GpioInt resource
>
> So I guess I'm curious about this Gpiolo/GpioInt resource number space...

In the above example:

GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{ // Pin list
76
}

The GPIO number (76) is relative to the GPIO controller in question
(\_SB.GPO0). 0 would be the first GPIO and so on...


\
 
 \ /
  Last update: 2014-10-29 12:01    [W:0.078 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site