[lkml]   [2014]   [Oct]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v6 0/6] Add initial support for Broadcom Cygnus SoC
This patchset contains initial support for Broadcom's Cygnus SoC based on our
iProc architecture. Initial support is minimal and includes just the mach
platform code, clock driver, and a basic device tree configuration. Peripheral
drivers will be submitted soon, as will device tree configurations for other
Cygnus board variants.

Changes from v5:
- removed one level of menu used in mach-bcm/Kconfig
- changed MAINTAINERS to use N: to support all files associated with iproc
and cygnus going forward
- updated bcm_cygnus_defconfig to remove some DEBUG options that greatly
hamper performance

Changes from v4:
- simple clock tree used. reworked clock driver will be submitted later
- fixed MAINTAINERS patchset error
- removed DEBUG_UART_8250 Kconfig.debug legacy support
- made ARCH_BCM_IPROC a silent Kconfig option
- removed multi_v7_defconfig as it is not needed at this time, can
support in future patchset but does not seem optimal configs for our
current usage.

Changes from v3:
- restart functionality removed. Will be added in a different patchset
in drivers/power
- removed NEON init sequence. Will be moved to bootloader
- cleaned up Kconfigs for ARCH_BCM_CYGNUS by removing unnecessary selects
- consolidated ARCH_BCM_IPROC with select from ARCH_BCM_CYGNUS and
- removed bcm911360_entphn binding
- added documentation for SoCs currently supported in Cygnus family

Changes from v2:
- rebased to 3.17 kernel

Changes from v1:
- Address code review comments as per previous responses.
- Copyright headers updated to remove Broadcom URL.
- mach platform code still contains hard coded addresses. These address are
the same for all Cygnus variants. Could you please provide guidance on where
they should go if you would still like them changed. There does not seem to
be a reason to change them to device tree as they do not change.

Jonathan Richardson (3):
ARM: cygnus: Initial support for Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
ARM: cygnus defconfig : Initial defconfig for Broadcom Cygnus SoC

Scott Branden (3):
ARM: dts: Enable Broadcom Cygnus SoC
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: mach-bcm: Consolidate currently supported IPROC SoCs

.../devicetree/bindings/arm/bcm/cygnus.txt | 31 +++
.../devicetree/bindings/clock/bcm-cygnus-clock.txt | 34 +++
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/bcm-cygnus-clock.dtsi | 73 ++++++
arch/arm/boot/dts/bcm-cygnus.dtsi | 109 +++++++++
arch/arm/boot/dts/bcm911360_entphn.dts | 22 ++
arch/arm/boot/dts/bcm911360k.dts | 22 ++
arch/arm/boot/dts/bcm958300k.dts | 22 ++
arch/arm/configs/bcm_cygnus_defconfig | 237 ++++++++++++++++++++
arch/arm/mach-bcm/Kconfig | 65 ++++--
arch/arm/mach-bcm/Makefile | 3 +
arch/arm/mach-bcm/bcm_cygnus.c | 26 +++
13 files changed, 641 insertions(+), 21 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/bcm/cygnus.txt
create mode 100644 Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt
create mode 100644 arch/arm/boot/dts/bcm-cygnus-clock.dtsi
create mode 100644 arch/arm/boot/dts/bcm-cygnus.dtsi
create mode 100644 arch/arm/boot/dts/bcm911360_entphn.dts
create mode 100644 arch/arm/boot/dts/bcm911360k.dts
create mode 100644 arch/arm/boot/dts/bcm958300k.dts
create mode 100644 arch/arm/configs/bcm_cygnus_defconfig
create mode 100644 arch/arm/mach-bcm/bcm_cygnus.c


 \ /
  Last update: 2014-10-22 04:41    [W:0.034 / U:4.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site