lkml.org 
[lkml]   [2014]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/3] input: stmpe: bias keypad columns properly
Date
All keypad column pins used as inputs should be pulled up
on the STMPE24xx, but this is not done by the current driver.
Add some logic that will do this properly. The STMPE1601 also
has a keypad controller, but explicitly does *NOT* require
you to set up any pull-ups.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/input/keyboard/stmpe-keypad.c | 37 +++++++++++++++++++++++++++++++++--
1 file changed, 35 insertions(+), 2 deletions(-)

diff --git a/drivers/input/keyboard/stmpe-keypad.c b/drivers/input/keyboard/stmpe-keypad.c
index d46391f48310..fe6e3f22eed7 100644
--- a/drivers/input/keyboard/stmpe-keypad.c
+++ b/drivers/input/keyboard/stmpe-keypad.c
@@ -52,6 +52,7 @@
* struct stmpe_keypad_variant - model-specific attributes
* @auto_increment: whether the KPC_DATA_BYTE register address
* auto-increments on multiple read
+ * @set_pullup: whether the pins need to have their pull-ups set
* @num_data: number of data bytes
* @num_normal_data: number of normal keys' data bytes
* @max_cols: maximum number of columns supported
@@ -61,6 +62,7 @@
*/
struct stmpe_keypad_variant {
bool auto_increment;
+ bool set_pullup;
int num_data;
int num_normal_data;
int max_cols;
@@ -81,6 +83,7 @@ static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
},
[STMPE2401] = {
.auto_increment = false,
+ .set_pullup = true,
.num_data = 3,
.num_normal_data = 2,
.max_cols = 8,
@@ -90,6 +93,7 @@ static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
},
[STMPE2403] = {
.auto_increment = true,
+ .set_pullup = true,
.num_data = 5,
.num_normal_data = 3,
.max_cols = 8,
@@ -185,7 +189,10 @@ static int stmpe_keypad_altfunc_init(struct stmpe_keypad *keypad)
unsigned int col_gpios = variant->col_gpios;
unsigned int row_gpios = variant->row_gpios;
struct stmpe *stmpe = keypad->stmpe;
+ u8 pureg = stmpe->regs[STMPE_IDX_GPPUR_LSB];
unsigned int pins = 0;
+ unsigned int pu_pins = 0;
+ int ret;
int i;

/*
@@ -202,8 +209,10 @@ static int stmpe_keypad_altfunc_init(struct stmpe_keypad *keypad)
for (i = 0; i < variant->max_cols; i++) {
int num = __ffs(col_gpios);

- if (keypad->cols & (1 << i))
+ if (keypad->cols & (1 << i)) {
pins |= 1 << num;
+ pu_pins |= 1 << num;
+ }

col_gpios &= ~(1 << num);
}
@@ -217,7 +226,31 @@ static int stmpe_keypad_altfunc_init(struct stmpe_keypad *keypad)
row_gpios &= ~(1 << num);
}

- return stmpe_set_altfunc(stmpe, pins, STMPE_BLOCK_KEYPAD);
+ ret = stmpe_set_altfunc(stmpe, pins, STMPE_BLOCK_KEYPAD);
+ if (ret)
+ return ret;
+
+ /*
+ * On STMPE24xx, set pin bias to pull-up on all keypad input
+ * pins (columns), this incidentally happen to be maximum 8 pins
+ * and placed at GPIO0-7 so only the LSB of the pull up register
+ * ever needs to be written.
+ */
+ if (variant->set_pullup) {
+ u8 val;
+
+ ret = stmpe_reg_read(stmpe, pureg);
+ if (ret)
+ return ret;
+
+ /* Do not touch unused pins, may be used for GPIO */
+ val = ret & ~pu_pins;
+ val |= pu_pins;
+
+ ret = stmpe_reg_write(stmpe, pureg, val);
+ }
+
+ return 0;
}

static int stmpe_keypad_chip_init(struct stmpe_keypad *keypad)
--
1.9.3


\
 
 \ /
  Last update: 2014-10-18 15:21    [W:0.040 / U:0.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site