lkml.org 
[lkml]   [2014]   [Oct]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/2] DT: iio: vadc: document dt binding
Thanks for the comments!

On 10/12/2014 02:05 AM, Hartmut Knaack wrote:
> Hi,
> two small issues inline.
> Stanimir Varbanov schrieb am 24.09.2014 14:56:
>> Document DT binding for Qualcomm SPMI PMIC voltage ADC
>> driver.
>>
>> Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
>> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
>> ---
>> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 130 ++++++++++++++++++++
>> 1 files changed, 130 insertions(+), 0 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> new file mode 100644
>> index 0000000..fa30300
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> @@ -0,0 +1,130 @@
>> +Qualcomm's SPMI PMIC voltage ADC
>> +
>> +SPMI PMIC voltage ADC (VADC) provides interface to clients to read
>> +voltage. A 15 bit ADC is used for voltage measurements. There are multiple
>> +peripherals to the VADC and the scope of the driver is to provide interface
>> +for the USR peripheral of the VADC.
>> +
>> +VADC node:
>> +
>> +- compatible:
>> + Usage: required
>> + Value type: <string>
>> + Definition: Should contain "qcom,spmi-vadc".
>> +
>> +- reg:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Base address in the SPMI PMIC register map.
>> +
>> +- address-cells:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Must be one.
>> +
>> +- size-cells:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Must be zero.
>> +
>> +- interrupts:
>> + Usage: optional
>> + Value type: <prop-encoded-array>
>> + Definition: End of conversion interrupt number. If this property does
>> + not exist polling will be used instead.
>> +
>> +- interrupt-names:
>> + Usage: optional
>> + Value type: <string>
>> + Definition: Should contain the interrupt name "eoc" (end of conversion).
>> +
>> +Channel node properties:
>> +
>> +- reg:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: AMUX channel number.
>> + See include/dt-bindings/iio/qcom,spmi-pmic-vadc.h
>> +
>> +- qcom,decimation:
>> + Usage: optional
>> + Value type: <u32>
>> + Definition: Sampling rate to use for the individual channel measurement.
>> + Quicker measurements can be made by reducing decimation ratio.
>> + Valid values are 512, 1024, 2048, 4096.
>> + If property is not found, default value of 512 will be used.
>> +
>> +- qcom,pre-scaling:
>> + Usage: optional
>> + Value type: <u32 array>
>> + Definition: Used for scaling the channel input signal before the signal is
>> + fed to VADC. The configuration for this node is to know the
>> + pre-determined ratio and use it for post scaling. Select one from
>> + the following options.
>> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
>> + If property is not found default value depending of chip will be used.
>> +
>> +- qcom,ratiometric:
>> + Usage: optional
>> + Value type: <empty>
>> + Definition: Channel calibration type. If this property is specified
>> + VADC will use the VDD reference(1.8V) and GND for channel
> Missing whitespace before opening parenthesis.
>> + calibration. If property is not found, channel will be
>> + calibrated with 625mV and 1.25V reference channels.
> There is a slight majority in using V instead of mv (2 : 1), so why not express everything in V?

No worries, will correct.

--
regards,
Stan


\
 
 \ /
  Last update: 2014-10-14 08:02    [W:0.151 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site