lkml.org 
[lkml]   [2014]   [Oct]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] pinctrl: baytrail: show output gpio state correctly on Intel Baytrail
On Mon, Oct 13, 2014 at 02:14:05PM -0500, Felipe Balbi wrote:
> On Mon, Oct 13, 2014 at 11:23:59AM -0700, David Cohen wrote:
> > Even if a gpio pin is set to output, we still need to set INPUT_EN bit
>
> here you say you're setting that bit.
>
> > to be able to read its value. Without this change, we'll always read low
> > level state.
> >
> > Cc: <stable@vger.kernel.org> # v3.14+
> > Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
> > ---
> >
> > Hi,
> >
> > I'm resending same v1 patch but now copying linux stable and linux gpio.
> > This patch is meant for all linux stable trees >= v3.14.
> >
> > Br, David
> > ---
> >
> > drivers/pinctrl/pinctrl-baytrail.c | 2 +-
> > 1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > diff --git a/drivers/pinctrl/pinctrl-baytrail.c b/drivers/pinctrl/pinctrl-baytrail.c
> > index e12e5b07f6d7..c23d8ded936d 100644
> > --- a/drivers/pinctrl/pinctrl-baytrail.c
> > +++ b/drivers/pinctrl/pinctrl-baytrail.c
> > @@ -318,7 +318,7 @@ static int byt_gpio_direction_output(struct gpio_chip *chip,
> > "Potential Error: Setting GPIO with direct_irq_en to output");
> >
> > reg_val = readl(reg) | BYT_DIR_MASK;
> > - reg_val &= ~BYT_OUTPUT_EN;
> > + reg_val &= ~(BYT_OUTPUT_EN | BYT_INPUT_EN);
>
> but code is clearing it. Also, you're not patching byt_gpio_get(), so
> you can't be 'reading its value' either. Quite frankly, this looks very
> fishy to me. Comments on BYT_OUTPUT_EN and BYT_INPUT_EN states that
> those bits are active low, meaning that clearing them enables that
> particular feature.
>
> How can you enable a pin to be both OUTPUT and INPUT ? Look like what
> you really want is:
>
> diff --git a/drivers/pinctrl/pinctrl-baytrail.c b/drivers/pinctrl/pinctrl-baytrail.c
> index e12e5b0..69f882d 100644
> --- a/drivers/pinctrl/pinctrl-baytrail.c
> +++ b/drivers/pinctrl/pinctrl-baytrail.c
> @@ -290,6 +290,7 @@ static int byt_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
>
> value = readl(reg) | BYT_DIR_MASK;
> value &= ~BYT_INPUT_EN; /* active low */
> + value |= BYT_OUTPUT_EN; /* disable output */
> writel(value, reg);
>
> spin_unlock_irqrestore(&vg->lock, flags);
> @@ -319,6 +320,7 @@ static int byt_gpio_direction_output(struct gpio_chip *chip,
>
> reg_val = readl(reg) | BYT_DIR_MASK;
> reg_val &= ~BYT_OUTPUT_EN;
> + value |= BYT_INPUT_EN; /* disable input */
>
> if (value)
> writel(reg_val | BYT_LEVEL, reg);
>
> completely untested however. Care to further explain why clearing both
> bits - thus enabling both INPUT and OUTPUT - is correct ?

Actually I really meant what I sent, but perhaps I misspoke during
explanation. We need to clear the bit to enable the functionality.

!BYT_INPUT_EN allows us to read the value. !BYT_OUTPUT_EN allows us to
set a value. If we want to set a value (acting as output) and still be
able to read via sysfs, we need to set both functionality (i.e. clear
both bits).

I'll resend the patch with a better comment.

Br, David

>
> --
> balbi




\
 
 \ /
  Last update: 2014-10-13 22:01    [W:0.096 / U:21.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site