lkml.org 
[lkml]   [2014]   [Jan]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH-v2 12/17] target/file: Add DIF protection init/format support
From
Date
On Wed, 2014-01-22 at 12:12 +0200, Sagi Grimberg wrote:
> On 1/22/2014 12:28 AM, Nicholas A. Bellinger wrote:
> > On Sun, 2014-01-19 at 14:31 +0200, Sagi Grimberg wrote:
> >> On 1/19/2014 4:44 AM, Nicholas A. Bellinger wrote:
> >>> From: Nicholas Bellinger <nab@linux-iscsi.org>
> >>>
> >>> This patch adds support for DIF protection init/format support into
> >>> the FILEIO backend.
> >>>
> >>> It involves using a seperate $FILE.protection for storing PI that is
> >>> opened via fd_init_prot() using the common pi_prot_type attribute.
> >>> The actual formatting of the protection is done via fd_format_prot()
> >>> using the common pi_prot_format attribute, that will populate the
> >>> initial PI data based upon the currently configured pi_prot_type.
> >>>
> >>> Based on original FILEIO code from Sagi.
> >> Nice! see comments below...
> >>

<SNIP>

> >>> +static void fd_init_format_buf(struct se_device *dev, unsigned char *buf,
> >>> + u32 unit_size, u32 *ref_tag, u16 app_tag,
> >>> + bool inc_reftag)
> >>> +{
> >>> + unsigned char *p = buf;
> >>> + int i;
> >>> +
> >>> + for (i = 0; i < unit_size; i += dev->prot_length) {
> >>> + *((u16 *)&p[0]) = 0xffff;
> >>> + *((__be16 *)&p[2]) = cpu_to_be16(app_tag);
> >>> + *((__be32 *)&p[4]) = cpu_to_be32(*ref_tag);
> >>> +
> >>> + if (inc_reftag)
> >>> + (*ref_tag)++;
> >>> +
> >>> + p += dev->prot_length;
> >>> + }
> >>> +}
> >>> +
> >>> +static int fd_format_prot(struct se_device *dev)
> >>> +{
> >>> + struct fd_dev *fd_dev = FD_DEV(dev);
> >>> + struct file *prot_fd = fd_dev->fd_prot_file;
> >>> + sector_t prot_length, prot;
> >>> + unsigned char *buf;
> >>> + loff_t pos = 0;
> >>> + u32 ref_tag = 0;
> >>> + int unit_size = FDBD_FORMAT_UNIT_SIZE * dev->dev_attrib.block_size;
> >>> + int rc, ret = 0, size, len;
> >>> + bool inc_reftag = false;
> >>> +
> >>> + if (!dev->dev_attrib.pi_prot_type) {
> >>> + pr_err("Unable to format_prot while pi_prot_type == 0\n");
> >>> + return -ENODEV;
> >>> + }
> >>> + if (!prot_fd) {
> >>> + pr_err("Unable to locate fd_dev->fd_prot_file\n");
> >>> + return -ENODEV;
> >>> + }
> >>> +
> >>> + switch (dev->dev_attrib.pi_prot_type) {
> >> redundant - see below.
> >>> + case TARGET_DIF_TYPE3_PROT:
> >>> + ref_tag = 0xffffffff;
> >>> + break;
> >>> + case TARGET_DIF_TYPE2_PROT:
> >>> + case TARGET_DIF_TYPE1_PROT:
> >>> + inc_reftag = true;
> >>> + break;
> >>> + default:
> >>> + break;
> >>> + }
> >>> +
> >>> + buf = vzalloc(unit_size);
> >>> + if (!buf) {
> >>> + pr_err("Unable to allocate FILEIO prot buf\n");
> >>> + return -ENOMEM;
> >>> + }
> >>> +
> >>> + prot_length = (dev->transport->get_blocks(dev) + 1) * dev->prot_length;
> >>> + size = prot_length;
> >>> +
> >>> + pr_debug("Using FILEIO prot_length: %llu\n",
> >>> + (unsigned long long)prot_length);
> >>> +
> >>> + for (prot = 0; prot < prot_length; prot += unit_size) {
> >>> +
> >>> + fd_init_format_buf(dev, buf, unit_size, &ref_tag, 0xffff,
> >>> + inc_reftag);
> >> I didn't send you my latest patches (my fault...).T10-PI format should
> >> only place
> >> escape values throughout the protection file (fill it with 0xff). so I
> >> guess in this case
> >> fd_init_formast_buf() boils down to memset(buf, 0xff, unit_size) once
> >> before the loop
> >> and just loop until prot_length writing buf, no need to address
> >> apptag/reftag...
> > Yeah, was thinking about just formatting with escape values as mentioned
> > above, but thought it might be useful to keep around for pre-populating
> > values apptag + reftag values for testing purposes.
> >
> > --nab
> >
>
> OK, but maybe it is better to do that under some debug configuration
> rather then always do that.
>

With the apptag escape in place from the format the host is going to
ignore the other areas, so this shouldn't really matter.

If it turns out to be a issue, we can just drop this code later.

--nab



\
 
 \ /
  Last update: 2014-01-22 23:21    [W:0.100 / U:0.544 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site