lkml.org 
[lkml]   [2014]   [Jan]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 12/28] drm/i2c: tda998x: add DT support
On Thu, Jan 09, 2014 at 12:03:24PM +0100, Jean-Francois Moine wrote:
> This patch adds DT support to the tda998x.
>
> As a side effect, now, the audio sample rate is always 48kHz and the
> audio clock is always set.
>
> Signed-off-by: Jean-Francois Moine <moinejf@free.fr>

This patch breaks audio through the renaming of variable names. When you
do such changes, *never* change all three together. Do them one at a time,
replacing all instances of one variable before moving on to the next one.
This avoids getting the names muddled up.

> - struct tda998x_encoder_params params;
> +
> + u8 audio_type; /* audio type */
> + u8 audio_frame[6];
> + u32 audio_port;

"audio type" is a pointless comment for a variable called "audio_type".
Explain what it is. It's the input format, which may be SPDIF or I2S.

> /* Set audio input source */
> - switch (p->audio_format) {
> + switch (priv->audio_type) {

So, "audio_format" has become "audio_type" here.

> @@ -698,7 +703,13 @@ tda998x_encoder_set_config(struct drm_encoder *encoder, void *params)
> VIP_CNTRL_2_SWAP_F(p->swap_f) |
> (p->mirr_f ? VIP_CNTRL_2_MIRR_F : 0);
>
> - priv->params = *p;
> + memcpy(priv->audio_frame, p->audio_frame,
> + sizeof priv->audio_frame);
> +
> + if (p->audio_cfg) {
> + priv->audio_port = p->audio_cfg;
> + priv->audio_type = p->audio_format;
> + }

Here, audio_port and audio_type are only written to if audio_cfg is
non-zero, which is not quite what is intended here. If you want DT
to override this, then make that explicit.

Moreover, we can see that this confirms that "audio_format" becomes
"audio_type", and "audio_cfg" becomes "audio_port".

> @@ -947,8 +958,8 @@ tda998x_encoder_mode_set(struct drm_encoder *encoder,
>
> tda998x_write_avi(priv, mode);
>
> - if (priv->params.audio_cfg)
> - tda998x_configure_audio(priv, mode, &priv->params);
> + if (priv->audio_type)
> + tda998x_configure_audio(priv, mode);

And here we have the real bug. "audio_cfg" has become "audio_type",
which in the case of SPDIF, is zero. Hence, with a SPDIF source,
tda998x_configure_audio() is no longer called.

--
FTTC broadband for 0.8mile line: 5.8Mbps down 500kbps up. Estimation
in database were 13.1 to 19Mbit for a good line, about 7.5+ for a bad.
Estimate before purchase was "up to 13.2Mbit".


\
 
 \ /
  Last update: 2014-01-11 19:21    [W:0.042 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site