Messages in this thread | ![/](/images/icornerl.gif) | | Date | Thu, 22 Aug 2013 18:00:31 +0200 | From | boris brezillon <> | Subject | Re: [PATCH 1/2] net/cadence/macb: add support for dt phy definition |
| |
Hello Florian,
On 22/08/2013 17:57, Boris BREZILLON wrote: > The macb driver only handle PHY description through platform_data > (macb_platform_data). > Thus, when using dt you cannot define phy properties like phy address or > phy irq pin. > > This patch makes use of the of_mdiobus_register to add support for > phy device definition using dt. > A fallback to the autoscan procedure is added in case there is no phy > devices defined in dt. > > Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com> > --- > drivers/net/ethernet/cadence/macb.c | 41 +++++++++++++++++++++++++++++------ > 1 file changed, 34 insertions(+), 7 deletions(-) > > diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c > index e866608..fe06ab0 100644 > --- a/drivers/net/ethernet/cadence/macb.c > +++ b/drivers/net/ethernet/cadence/macb.c > @@ -27,6 +27,7 @@ > #include <linux/phy.h> > #include <linux/of.h> > #include <linux/of_device.h> > +#include <linux/of_mdio.h> > #include <linux/of_net.h> > #include <linux/pinctrl/consumer.h> > > @@ -314,6 +315,7 @@ static int macb_mii_probe(struct net_device *dev) > int macb_mii_init(struct macb *bp) > { > struct macb_platform_data *pdata; > + struct device_node *np; > int err = -ENXIO, i; > > /* Enable management port */ > @@ -335,21 +337,46 @@ int macb_mii_init(struct macb *bp) > bp->mii_bus->parent = &bp->dev->dev; > pdata = bp->pdev->dev.platform_data; > > - if (pdata) > - bp->mii_bus->phy_mask = pdata->phy_mask; > - > bp->mii_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL); > if (!bp->mii_bus->irq) { > err = -ENOMEM; > goto err_out_free_mdiobus; > } > > - for (i = 0; i < PHY_MAX_ADDR; i++) > - bp->mii_bus->irq[i] = PHY_POLL; > - > dev_set_drvdata(&bp->dev->dev, bp->mii_bus); > > - if (mdiobus_register(bp->mii_bus)) > + np = bp->pdev->dev.of_node; > + if (np) { > + /* try dt phy registration */ > + err = of_mdiobus_register(bp->mii_bus, np); > + > + /* fallback to standard phy registration if no phy were > + found during dt phy registration */ > + if (!err && !phy_find_first(bp->mii_bus)) { > + for (i = 0; i < PHY_MAX_ADDR; i++) { > + struct phy_device *phydev; > + > + phydev = mdiobus_scan(bp->mii_bus, i); > + if (IS_ERR(phydev)) { > + err = PTR_ERR(phydev); > + break; > + } > + } > +
This is were I need the mdiobus_full_scan function.
> + if (err) > + goto err_out_unregister_bus; > + } > + } else { > + for (i = 0; i < PHY_MAX_ADDR; i++) > + bp->mii_bus->irq[i] = PHY_POLL; > + > + if (pdata) > + bp->mii_bus->phy_mask = pdata->phy_mask; > + > + err = mdiobus_register(bp->mii_bus); > + } > + > + if (err) > goto err_out_free_mdio_irq; > > if (macb_mii_probe(bp->dev) != 0) {
| ![\](/images/icornerr.gif) |