lkml.org 
[lkml]   [2013]   [Jul]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] ARM: dts: USB for Tegra114 Dalmore
Hello,

On 31/07/13 21:18, Sergei Shtylyov wrote:
> Hello.
>
> On 07/31/2013 09:42 PM, Tuomas Tynkkynen wrote:
>
>> From: Mikko Perttunen <mperttunen@nvidia.com>
>
>> Device tree entries for the three EHCI controllers on Tegra114.
>> Enables the the third controller (USB host) on Dalmore.
>
> I would have done the board patch separately from the SoC one.
>
>> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
> [...]
>
>> diff --git a/arch/arm/boot/dts/tegra114.dtsi
>> b/arch/arm/boot/dts/tegra114.dtsi
>> index abf6c40..2905145 100644
>> --- a/arch/arm/boot/dts/tegra114.dtsi
>> +++ b/arch/arm/boot/dts/tegra114.dtsi
>> @@ -430,6 +430,68 @@
>> status = "disable";
>> };
>>
>> + usb@7d000000 {
>> + compatible = "nvidia,tegra30-ehci", "usb-ehci";
>> + reg = <0x7d000000 0x4000>;
>> + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
>> + phy_type = "utmi";
>> + clocks = <&tegra_car TEGRA114_CLK_USBD>;
>> + nvidia,phy = <&phy1>;
>> + status = "disabled";
>> + };
>> +
>> + phy1: usb-phy@7d000000 {
>
> At the same address as the previous node?

Yes. The first node is for the EHCI driver and the second for the PHY
driver. There is some overlap in the exact registers used, so both
drives map the whole USB controller block.

>
>> + compatible = "nvidia,tegra30-usb-phy";
>> + reg = <0x7d000000 0x4000 0x7d000000 0x4000>;
>
> Hm, there must be some mistake: two similar register ranges.

The second range is used to configure the UTMI pad registers. All the
UTMI pad registers are located in the first USB controller's range.

>> + usb@7d008000 {
>> + compatible = "nvidia,tegra30-ehci", "usb-ehci";
>> + reg = <0x7d008000 0x4000>;
>> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
>> + phy_type = "utmi";
>> + clocks = <&tegra_car TEGRA114_CLK_USB3>;
>> + nvidia,phy = <&phy3>;
>> + status = "disabled";
>> + };
>> +
>> + phy3: usb-phy@7d008000 {
>
> Again at the same address as previous node?
>
>> + compatible = "nvidia,tegra30-usb-phy";
>> + reg = <0x7d008000 0x4000 0x7d000000 0x4000>;
>
> Second range conflicts with previous nodes.
>
> WBR, Sergei

All these entries mapping the same address are expected. See
arch/arm/boot/dts/tegra20.dtsi for an existing example of Tegra USB
bindings.


\
 
 \ /
  Last update: 2013-07-31 21:41    [W:0.157 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site