Messages in this thread | | | Date | Tue, 30 Jul 2013 10:26:04 +0800 | From | Robin Gong <> | Subject | Re: regulator: pfuze100: A few small questions |
| |
On Mon, Jul 29, 2013 at 11:44:40PM +0800, Axel Lin wrote: > >> Current code adjust min_uV and uV_step when SW2~SW4 high bit is set. > >> I'm wondering if n_voltages is correct or not in this case because > >> the n_voltages is calculated by original equation (max-min/step + 1). > >> What is the max_uV when SW2~SW4 high bit is set? > >> > > If high bit set(bit6, bit0~5:vsel), min_uV/step will change from 0.4V/25mV to > > 0.8V/50mV,but the n_voltages will kept the same. > > For example,SW2 will vary from 0.4V to 1.975V(0x0~0x3f),if bit6 set 0(high bit) > > SW2 will vary from 0.8V to 3.3V(0x40~0x72,0x72~0x7f:reversed). > > Please ignore bit7 or consider it as 0. > > Hi Robin, > According to your description: > BIT6 is clear: 0.4V ~ 1.975V , step 25mV (0x0~0x3f) > BIT6 is set: 0.8V ~ 3.3V, step 50mV (0x40~0x72,0x72~0x7f:reversed) > > For SW2/SW3A/SW3B/SW4: > I think current implementation is wrong. > The supported voltage range should cover the whole range: 0.4V ~ 3.3V. > Hi Alex, Yes,the default setting of SW2 ~SW4in the regulator array is 0.4V~1.975V (Bit6 clear),and my code will check the true setting of Bit6. If Bit6=1 I will change min_uV from 0.4V to 0.8V ,step from 25mV to 50mV as what hardware define. I don't think we should mix the two define as what you mean 0.4V~3.3V. Because for every pfuze100 chip, the voltage of SW2~SW4 is 0.4V~1.975V or 0.8V~3.3V, not 0.4V~3.3V(from software view,Bit6 only readable).
> You need to implement set_voltage_sel/get_voltage_sel: > For 0.4V ~ 1.975V, use 25mV step and clear BIT6. > For 2V ~ 3.3V, use 50mV step and set BIT6 > No,should be: For 0.8V~3.3V, use 50mV step if set BIT6 > And use regulator_list_voltage_linear_range / regulator_map_voltage_linear_range > Yes, I have used regulator_list_voltage_linear to list voltage, so that regulator core will regulator_map_voltage_linear to find the right voltage. > Below list the register value and voltage mapping: > > reg volt (reg with BIT6 is set) > ================================ > 0x00 400000 > 0x01 425000 > 0x02 450000 > 0x03 475000 > 0x04 500000 > ... ...... > 0x0e 750000 > 0x0f 775000 > 0x10 800000 (0x40) > 0x11 825000 > 0x12 850000 (0x41) > 0x13 875000 > 0x14 900000 (0x42) > 0x15 925000 > 0x16 950000 (0x43) > 0x17 975000 > 0x18 1000000 (0x44) > 0x19 1025000 > 0x1a 1050000 (0x45) > 0x1b 1075000 > 0x1c 1100000 (0x46) > 0x1d 1125000 > 0x1e 1150000 (0x47) > 0x1f 1175000 > ... ....... > 0x3c 1950000 (0x57) > 0x3f 1975000 > 2000000 (0x58) > 2050000 (0x59) > 2100000 (0x5a) > ..... > 3300000 (0x72) > Great, the voltage mapping is right. > Regards, > Axel >
| |