lkml.org 
[lkml]   [2013]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 2/4] gpu: host1x: add runtime pm support for gr2d
On Thursday 13 June 2013 08:44 PM, Stephen Warren wrote:
> On 06/13/2013 03:53 AM, Mayuresh Kulkarni wrote:
>
> Patch description?

I thought the patch subject is sufficient to tell what it is it doing.
Description here would be repetition in my opinion.

Also, the cover letter for the patch-set series is verbose enough.

>
>
>> diff --git a/drivers/gpu/host1x/drm/gr2d.c b/drivers/gpu/host1x/drm/gr2d.c
>
>> +#ifdef CONFIG_PM_RUNTIME
>> + pm_runtime_enable(&pdev->dev);
>> + pm_runtime_get_sync(&pdev->dev);
>> +#else
>> err = clk_prepare_enable(gr2d->clk);
>> if (err) {
>> dev_err(dev, "cannot turn on clock\n");
>> return err;
>> }
>> +#endif
>
> The #else block here is a cut/paste of the body of
> gr2d_runtime_resume(). It'd be better to call that function instead. The
> following is what I ended up with in the Tegra ASoC driver in order to
> support runtime PM on or off:
>
> pm_runtime_enable(&pdev->dev);
> if (!pm_runtime_enabled(&pdev->dev)) {
> ret = tegra20_i2s_runtime_resume(&pdev->dev);
> if (ret)
> goto err_pm_disable;
> }
>

Thanks for the tip. Runtime detection is better than compile time here.

>> @@ -328,10 +338,51 @@ static int __exit gr2d_remove(struct platform_device *pdev)
>>
>> host1x_channel_free(gr2d->channel);
>> clk_disable_unprepare(gr2d->clk);
>
> Don't you need to remove that clk disable, or make it conditional upon
> !PM_RUNTIME?

Yes you are correct.

>
>> +#ifdef CONFIG_PM_RUNTIME
>> + pm_runtime_disable(&pdev->dev);
>> +#endif
>
> Similarly, perhaps something like the following here:
>
> pm_runtime_disable(&pdev->dev);
> if (!pm_runtime_status_suspended(&pdev->dev))
> tegra20_i2s_runtime_suspend(&pdev->dev);
>
>> @ -591,10 +592,18 @@ int host1x_job_submit(struct host1x_job *job)
>> {
>> struct host1x *host = dev_get_drvdata(job->channel->dev->parent);
>>
>> +#ifdef CONFIG_PM_RUNTIME
>> + pm_runtime_get_sync(job->channel->dev);
>> +#endif
>> +
>> return host1x_hw_channel_submit(host, job);
>> }
>>
>> int host1x_job_complete(struct host1x_job *job)
>> {
>> +#ifdef CONFIG_PM_RUNTIME
>> + return pm_runtime_put(job->channel->dev);
>> +#else
>> return 0;
>> +#endif
>> }
>
> I don't think you need any of those ifdefs; simply call the
> pm_runtime_*() functions all the time, and they'll be successful no-ops
> if !PM_RUNTIME.
>
OK. But I thought it will be better to be verbose (which is not needed).



\
 
 \ /
  Last update: 2013-06-14 17:01    [W:0.053 / U:0.520 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site