lkml.org 
[lkml]   [2013]   [Mar]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] Remove acpi_memory_info->failed bit
Hi Toshi,

2013/03/20 0:03, Toshi Kani wrote:
> On Mon, 2013-03-18 at 11:19 +0900, Yasuaki Ishimatsu wrote:
>> Hi Toshi,
>>
>> Sorry for the late reply
>>
>> 2013/03/13 23:50, Toshi Kani wrote:
>>> On Wed, 2013-03-13 at 15:54 +0900, Yasuaki Ishimatsu wrote:
>>>> At http://marc.info/?l=linux-acpi&m=135769405622667&w=2 thread,
>>>> Toshi Kani mentioned as follows:
>>>>
>>>> "I have a question about the change you made in commit 65479472 in
>>>> acpi_memhotplug.c. This change seems to require that
>>>> acpi_memory_enable_device() calls add_memory() to add all memory ranges
>>>> represented by memory device objects at boot-time, and keep the results
>>>> be used for hot-remove.
>>>>
>>>> If I understand it right, this add_memory() call fails with EEXIST at
>>>> boot-time since all memory ranges should have been added from EFI memory
>>>> table (or e820) already. This results all memory ranges be marked as !
>>>> enabled & !failed. I think this means that we cannot hot-delete any
>>>> memory ranges presented at boot-time since acpi_memory_remove_memory()
>>>> only calls remove_memory() when the enabled flag is set. Is that
>>>> correct?"
>>>>
>>>> Above mention is correct. Thus even if memory device supports hotplug,
>>>> memory presented at boot-time cannot be hot removed since the memory
>>>> device's acpi_memory_info->enabled is always 0.
>>>>
>>>> This patch changes to set 1 to "acpi_memory_info->enabled" of memory
>>>> device presented at boot-time for hot removing the memory device.
>>>>
>>>> Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
>>>>
>>>> ---
>>>> drivers/acpi/acpi_memhotplug.c | 4 ++--
>>>> 1 files changed, 2 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c
>>>> index da1f82b..88fd46a 100644
>>>> --- a/drivers/acpi/acpi_memhotplug.c
>>>> +++ b/drivers/acpi/acpi_memhotplug.c
>>>> @@ -254,8 +254,8 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device)
>>>> continue;
>>>> }
>>>>
>>>> - if (!result)
>>>> - info->enabled = 1;
>>>> + info->enabled = 1;
>>>
>>> Do we still need to keep the enable bit? I think !failed means enabled
>>> with this change.
>>
>> For controlling memory hotplug, we need either failed bit or enabled bit.
>> So I want to remove failed bit as follows:
>>
>> ---
>>
>> acpi_memory_info has enabled bit and failed bit for controlling memory
>> hotplug. But we don't need to keep both bits.
>>
>> The patch removes acpi_memory_info->failed bit.
>
> Thanks for the update. Which branch does this patch apply to? I tried
> several, but could not apply.

These patches are based on linux-3.9-rc3.
O.K. I'll make them based on linux-pm.git/bleeding-edge.

Thanks,
Yasuaki Ishimatsu

> -Toshi
>
>




\
 
 \ /
  Last update: 2013-03-21 01:41    [W:0.064 / U:0.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site