lkml.org 
[lkml]   [2013]   [Mar]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/4] tty: max310x: Use dev_pm_ops
On 03/11/2013 07:41 PM, Alexander Shiyan wrote:
>> On 03/11/2013 07:10 PM, Alexander Shiyan wrote:
>>> Hello.
>>>
>>>> Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
>>>> max310x driver.
>>>>
>>>> Cc: Alexander Shiyan <shc_work@mail.ru>
>>>> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
>>>> ---
>>>> drivers/tty/serial/max310x.c | 24 ++++++++++++++++--------
>>>> 1 file changed, 16 insertions(+), 8 deletions(-)
>>>>
>>>> diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
>>>> index 0c2422c..8941e64 100644
>>>> --- a/drivers/tty/serial/max310x.c
>>>> +++ b/drivers/tty/serial/max310x.c
>>>> @@ -881,12 +881,14 @@ static struct uart_ops max310x_ops = {
>>>> .verify_port = max310x_verify_port,
>>>> };
>>>>
>>>> -static int max310x_suspend(struct spi_device *spi, pm_message_t state)
>>>> +#ifdef CONFIG_PM_SLEEP
>>>> +
>>>> +static int max310x_suspend(struct device *dev)
>>>> {
>>>> int ret;
>>>> - struct max310x_port *s = dev_get_drvdata(&spi->dev);
>>>> + struct max310x_port *s = dev_get_drvdata(dev);
>>>>
>>>> - dev_dbg(&spi->dev, "Suspend\n");
>>>> + dev_dbg(dev, "Suspend\n");
>>>>
>>>> ret = uart_suspend_port(&s->uart, &s->port);
>>>>
>>>> @@ -905,11 +907,11 @@ static int max310x_suspend(struct spi_device *spi, pm_message_t state)
>>>> return ret;
>>>> }
>>>>
>>>> -static int max310x_resume(struct spi_device *spi)
>>>> +static int max310x_resume(struct device *dev)
>>>> {
>>>> - struct max310x_port *s = dev_get_drvdata(&spi->dev);
>>>> + struct max310x_port *s = dev_get_drvdata(dev);
>>>>
>>>> - dev_dbg(&spi->dev, "Resume\n");
>>>> + dev_dbg(dev, "Resume\n");
>>>>
>>>> if (s->pdata->suspend)
>>>> s->pdata->suspend(0);
>>>> @@ -928,6 +930,13 @@ static int max310x_resume(struct spi_device *spi)
>>>> return uart_resume_port(&s->uart, &s->port);
>>>> }
>>>>
>>>> +static SIMPLE_DEV_PM_OPS(max310x_pm_ops, max310x_suspend, max310x_resume);
>>>> +#define MAX310X_PM_OPS (&max310x_pm_ops)
>>>> +
>>>> +#else
>>>> +#define MAX310X_PM_OPS NULL
>>>> +#endif
>>>> +
>>>> #ifdef CONFIG_GPIOLIB
>>>> static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset)
>>>> {
>>>> @@ -1242,11 +1251,10 @@ static struct spi_driver max310x_driver = {
>>>> .driver = {
>>>> .name = "max310x",
>>>> .owner = THIS_MODULE,
>>>> + .pm = MAX310X_PM_OPS,
>>>
>>> Check for CONFIG_PM_SLEEP not necessary at all.
>>> <linux/pm.h> will do all for us.
>>
>> No it wont, you'll end up with a dev_pm_ops struct full of zeros and two
> I.e. NULL, it is OK.

But what's the point of keeping it around?

>
>> warnings from your compiler about unused functions.
> I think attribute "__maybe_unused" can help here.

Or a #ifdef

>
>>>> },
>>>> .probe = max310x_probe,
>>>> .remove = max310x_remove,
>>>> - .suspend = max310x_suspend,
>>>> - .resume = max310x_resume,
>>>> .id_table = max310x_id_table,
>>>> };
>>>> module_spi_driver(max310x_driver);
>>>> --
>>>> 1.8.0
>>>
>>> ---
>
> ---



\
 
 \ /
  Last update: 2013-03-11 20:23    [W:0.053 / U:0.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site