lkml.org 
[lkml]   [2013]   [Mar]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v2 0/5] ARM: at91: fix hanged boot
Date
These patches fix a few severe issues affecting most AT91 SOCs where
boot can hang after a non-general reset, and where the only way to get
the system booting again is to do a general reset -- something which
could require physically removing any backup battery.

The problems stem from the fact that the RTC and RTT-peripherals are
powered by backup power (VDDBU) and are not reset on wake-up, user,
watchdog or software reset. Consequently, RTC and RTT-alarms and their
interrupts may be enabled at boot, leading to a system lock-up when an
interrupt arrives on the shared system-interrupt line before the
appropriate handler (e.g. RTC-driver) has been installed.

The easiest way to trigger this is to simply wake up from an RTC-alarm
on at91sam9g45. The RTC-driver currently does not disable interrupts at
shutdown so even after a clean shut-down the system will always hang
after waking up.

The first patch fixes this very general case of RTC-wake up after a
clean shutdown in the RTC-driver and is marked for stable as it is
perfectly straight-forward. [ Note that the other, RTT-based, AT91
RTC-driver already disables its interrupts at shutdown. ]

The more general problem can be triggered, for example, by doing a
user-reset while updating the RTC-time or if an RTC or RTT-alarm goes
off after a non-clean shutdown.

To fix this I propose that arch-code should mask the relevant interrupts
before enabling the system interrupt at early boot, and this is what
the fifth patch does. To access the RTC-registers I choose to revert a
recent patch that moved the register definitions to drivers/rtc.

Arguably, the relevant interrupts could also be disabled in bootloaders,
but I suggest fixing it in the kernel once and for all.

The patches have been tested on at91sam9263 and at91sam9g45 (non-DT),
and compile-tested for the other SOCs and DT.

Johan


v2:
- add DT-support
- make sys_irq_mask non-mandatory


Johan Hovold (5):
ARM: at91/rtc: fix boot after RTC wake-up
ARM: at91/dts: add RTC nodes
ARM: at91/dts: add RTT nodes
Revert "arm: at91: move at91rm9200 rtc header in drivers/rtc"
ARM: at91: fix hanged boot

arch/arm/boot/dts/at91rm9200.dtsi | 5 ++
arch/arm/boot/dts/at91sam9260.dtsi | 5 ++
arch/arm/boot/dts/at91sam9263.dtsi | 10 ++++
arch/arm/boot/dts/at91sam9g45.dtsi | 10 ++++
arch/arm/boot/dts/at91sam9n12.dtsi | 5 ++
arch/arm/boot/dts/at91sam9x5.dtsi | 5 ++
arch/arm/mach-at91/at91sam9260.c | 6 ++
arch/arm/mach-at91/at91sam9261.c | 6 ++
arch/arm/mach-at91/at91sam9263.c | 7 +++
arch/arm/mach-at91/at91sam9g45.c | 7 +++
arch/arm/mach-at91/at91sam9rl.c | 7 +++
arch/arm/mach-at91/generic.h | 2 +
arch/arm/mach-at91/include/mach/at91_rtc.h | 75 +++++++++++++++++++++++++
arch/arm/mach-at91/setup.c | 88 ++++++++++++++++++++++++++++++
arch/arm/mach-at91/soc.h | 1 +
drivers/rtc/rtc-at91rm9200.c | 11 +++-
drivers/rtc/rtc-at91rm9200.h | 75 -------------------------
17 files changed, 249 insertions(+), 76 deletions(-)
create mode 100644 arch/arm/mach-at91/include/mach/at91_rtc.h
delete mode 100644 drivers/rtc/rtc-at91rm9200.h

--
1.8.1.5



\
 
 \ /
  Last update: 2013-03-11 20:03    [W:1.854 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site