lkml.org 
[lkml]   [2013]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/4] spi: s3c64xx: modified error interrupt handling and init
Date
Hi Girish,

On Wednesday 06 of February 2013 12:12:29 Girish KS wrote:
> On Wed, Feb 6, 2013 at 2:26 AM, Grant Likely <grant.likely@secretlab.ca>
wrote:
> > On Tue, 5 Feb 2013 15:09:41 -0800, Girish K S
<girishks2000@gmail.com> wrote:
> >> The status of the interrupt is available in the status register,
> >> so reading the clear pending register and writing back the same
> >> value will not actually clear the pending interrupts. This patch
> >> modifies the interrupt handler to read the status register and
> >> clear the corresponding pending bit in the clear pending register.
> >>
> >> Modified the hwInit function to clear all the pending interrupts.
> >>
> >> Signed-off-by: Girish K S <ks.giri@samsung.com>
> >> ---
> >>
> >> drivers/spi/spi-s3c64xx.c | 41
> >> +++++++++++++++++++++++++---------------- 1 file changed, 25
> >> insertions(+), 16 deletions(-)
> >>
> >> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
> >> index ad93231..b770f88 100644
> >> --- a/drivers/spi/spi-s3c64xx.c
> >> +++ b/drivers/spi/spi-s3c64xx.c
> >> @@ -997,25 +997,30 @@ static irqreturn_t s3c64xx_spi_irq(int irq,
> >> void *data)>>
> >> {
> >>
> >> struct s3c64xx_spi_driver_data *sdd = data;
> >> struct spi_master *spi = sdd->master;
> >>
> >> - unsigned int val;
> >> + unsigned int val, clr = 0;
> >>
> >> - val = readl(sdd->regs + S3C64XX_SPI_PENDING_CLR);
> >> + val = readl(sdd->regs + S3C64XX_SPI_STATUS);
> >>
> >> - val &= S3C64XX_SPI_PND_RX_OVERRUN_CLR |
> >> - S3C64XX_SPI_PND_RX_UNDERRUN_CLR |
> >> - S3C64XX_SPI_PND_TX_OVERRUN_CLR |
> >> - S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
> >> -
> >> - writel(val, sdd->regs + S3C64XX_SPI_PENDING_CLR);
> >> -
> >> - if (val & S3C64XX_SPI_PND_RX_OVERRUN_CLR)
> >> + if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) {
> >> + clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR;
> >>
> >> dev_err(&spi->dev, "RX overrun\n");
> >>
> >> - if (val & S3C64XX_SPI_PND_RX_UNDERRUN_CLR)
> >> + }
> >> + if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) {
> >> + clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR;
> >>
> >> dev_err(&spi->dev, "RX underrun\n");
> >>
> >> - if (val & S3C64XX_SPI_PND_TX_OVERRUN_CLR)
> >> + }
> >> + if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) {
> >> + clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR;
> >>
> >> dev_err(&spi->dev, "TX overrun\n");
> >>
> >> - if (val & S3C64XX_SPI_PND_TX_UNDERRUN_CLR)
> >> + }
> >> + if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) {
> >> + clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
> >>
> >> dev_err(&spi->dev, "TX underrun\n");
> >>
> >> + }
> >> +
> >> + /* Clear the pending irq by setting and then clearing it */
> >> + writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
> >> + writel(clr & ~clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
> >
> > Wait, what? clr & ~clr == 0 Always. What are you actually trying
> > to do here?
> The user manual says, wirting 1 to the pending clear register clears
> the interrupt (its not auto clear to 0). so i need to explicitly reset
> those bits thats what the 2nd write does

I have looked through user's manuals of different Samsung SoCs. All of
them said that writing 1 to a bit clears the corresponding interrupt, but
none of them contain any note that it must be manually cleared to 0.

In addition the expression

clr & ~clr

makes no sense, because it is equal to 0.

If you really need to clear those bits manually (and I don't think so),
you should replace this expression with 0.

Best regards,
--
Tomasz Figa
Samsung Poland R&D Center
SW Solution Development, Linux Platform



\
 
 \ /
  Last update: 2013-02-07 12:43    [W:0.106 / U:0.572 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site