lkml.org 
[lkml]   [2013]   [Feb]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2 2/3] mmc: davinci_mmc: add DT support
Date
Hi Mark,

On Fri, Feb 08, 2013 at 11:55:09, Manjunathappa, Prakash wrote:
> Hi Mark,
>
> On Thu, Feb 07, 2013 at 16:16:56, Mark Rutland wrote:
> > Hello,
> >
> > I have a couple of comments on the dt bindings and the way it's parsed.
> >
>
> Thanks for your review comments.
>
> > On Thu, Feb 07, 2013 at 07:57:04AM +0000, Manjunathappa, Prakash wrote:
> > > Adds device tree support for davinci_mmc. Also add binding documentation.
> > > Tested in non-dma PIO mode and without GPIO card_detect/write_protect
> > > option because of dependencies on EDMA and GPIO module DT support.
> > >
> > > Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
> > > Cc: linux-mmc@vger.kernel.org
> > > Cc: linux-arm-kernel@lists.infradead.org
> > > Cc: linux-kernel@vger.kernel.org
> > > Cc: davinci-linux-open-source@linux.davincidsp.com
> > > Cc: devicetree-discuss@lists.ozlabs.org
> > > Cc: cjb@laptop.org
> > > Cc: Sekhar Nori <nsekhar@ti.com>
> > > Cc: mporter@ti.com
> > > ---
> > > Since v1:
> > > Modified DT parse function to take default values and accomodate controller
> > > version in compatible field.
> > >
> > > .../devicetree/bindings/mmc/davinci_mmc.txt | 30 ++++++++
> > > drivers/mmc/host/davinci_mmc.c | 70 +++++++++++++++++++-
> > > 2 files changed, 99 insertions(+), 1 deletions(-)
> > > create mode 100644 Documentation/devicetree/bindings/mmc/davinci_mmc.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt
> > > new file mode 100644
> > > index 0000000..6717ab1
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt
> > > @@ -0,0 +1,30 @@
> > > +* TI Highspeed MMC host controller for DaVinci
> > > +
> > > +The Highspeed MMC Host Controller on TI DaVinci family
> > > +provides an interface for MMC, SD and SDIO types of memory cards.
> > > +
> > > +This file documents the properties used by the davinci_mmc driver.
> > > +
> > > +Required properties:
> > > +- compatible:
> > > + Should be "ti,davinci-mmc-da830": for da830, da850, dm365
> > > + Should be "ti,davinci-mmc-dm355": for dm355, dm644x
> > > +
> > > +Optional properties:
> > > +- bus-width: Number of data lines, can be <4>, or <8>, default <1>
> > > +- max-frequency: Maximum operating clock frequency, default 25MHz.
> > > +- mmc-cap-mmc-highspeed: Indicates support for MMC in high speed mode
> > > +- mmc-cap-sd-highspeed: Indicates support for SD in high speed mode
> >
> > I thought the last two were derivable from max-frequency?
> >
>
> Yes, but I see below comment that it doesnot support MMC/SD.
> arch/arm/mach-davinci/devices.c: davinci_setup_mmc
> "
> * FIXME dm6441 (no MMC/SD), dm357 (one), and dm335 (two) are
> * not handled right here ...
> */"
> I was wondering how do we support such platforms, so I thought it is necessary
> to have these. But I see that on da850-evm even on skipping above flags EVM is able
> to detect card, does it mean there is no way to specify "no SD/MMC" capability?
> I will remove these and decide highspeed capability based on max-frequency.
>

Since this comment also applies for existing non-DT driver, I will plan to take
up activity later. For now I will submit next version of DT support patch
excluding highspeed card capability.

Thanks,
Prakash

[...]



\
 
 \ /
  Last update: 2013-02-11 07:21    [W:0.075 / U:0.368 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site