lkml.org 
[lkml]   [2013]   [Feb]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4] i2c: exynos5: add High Speed I2C controller driver
Date
Adds support for High Speed I2C driver found in Exynos5 and later
SoCs from Samsung. This driver currently supports Auto mode.

Driver only supports Device Tree method.
Note: Added debugfs support for registers view, not tested.

Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
---
Help please,

Usual reads and writes are happening. But, when i try doing
i2cdetect -y 0 0x10 0x59; It throws me continous interrupts at 0x1a
i2cdetect -y 0 0x50 0x64; It throws me continous interrupts at 0x63

There are eeproms from 0x50 till 0x58
wm8994 codec at 0x1a

Kindly, can anyone explain this behaviour.

drivers/i2c/busses/Kconfig | 7 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-exynos5.c | 754 ++++++++++++++++++++++++++++++++++++++
3 files changed, 762 insertions(+)
create mode 100644 drivers/i2c/busses/i2c-exynos5.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index bdca511..4caea76 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -618,6 +618,13 @@ config I2C_S3C2410
Say Y here to include support for I2C controller in the
Samsung SoCs.

+config I2C_EXYNOS5
+ tristate "Exynos5 high-speed I2C driver"
+ depends on ARCH_EXYNOS5
+ help
+ Say Y here to include support for High-speed I2C controller in the
+ Exynos5 based Samsung SoCs.
+
config I2C_S6000
tristate "S6000 I2C support"
depends on XTENSA_VARIANT_S6000
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 6181f3f..4b1548c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o
obj-$(CONFIG_I2C_PXA) += i2c-pxa.o
obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o
obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o
+obj-$(CONFIG_I2C_EXYNOS5) += i2c-exynos5.o
obj-$(CONFIG_I2C_S6000) += i2c-s6000.o
obj-$(CONFIG_I2C_SH7760) += i2c-sh7760.o
obj-$(CONFIG_I2C_SH_MOBILE) += i2c-sh_mobile.o
diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
new file mode 100644
index 0000000..6bd5637
--- /dev/null
+++ b/drivers/i2c/busses/i2c-exynos5.c
@@ -0,0 +1,754 @@
+/**
+ * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/debugfs.h>
+
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/of_irq.h>
+#include <linux/of_i2c.h>
+
+/* Register Map */
+#define HSI2C_CTL 0x00
+#define HSI2C_FIFO_CTL 0x04
+#define HSI2C_TRAILIG_CTL 0x08
+#define HSI2C_CLK_CTL 0x0C
+#define HSI2C_CLK_SLOT 0x10
+#define HSI2C_INT_ENABLE 0x20
+#define HSI2C_INT_STATUS 0x24
+#define HSI2C_ERR_STATUS 0x2C
+#define HSI2C_FIFO_STATUS 0x30
+#define HSI2C_TX_DATA 0x34
+#define HSI2C_RX_DATA 0x38
+#define HSI2C_CONF 0x40
+#define HSI2C_AUTO_CONF 0x44
+#define HSI2C_TIMEOUT 0x48
+#define HSI2C_MANUAL_CMD 0x4C
+#define HSI2C_TRANS_STATUS 0x50
+#define HSI2C_TIMING_HS1 0x54
+#define HSI2C_TIMING_HS2 0x58
+#define HSI2C_TIMING_HS3 0x5C
+#define HSI2C_TIMING_FS1 0x60
+#define HSI2C_TIMING_FS2 0x64
+#define HSI2C_TIMING_FS3 0x68
+#define HSI2C_TIMING_SLA 0x6C
+#define HSI2C_ADDR 0x70
+
+/* I2C_CTL Register bits */
+#define HSI2C_FUNC_MODE_I2C (1u << 0)
+#define HSI2C_MASTER (1u << 3)
+#define HSI2C_RXCHON (1u << 6)
+#define HSI2C_TXCHON (1u << 7)
+#define HSI2C_SW_RST (1u << 31)
+
+/* I2C_FIFO_CTL Register bits */
+#define HSI2C_RXFIFO_EN (1u << 0)
+#define HSI2C_TXFIFO_EN (1u << 1)
+#define HSI2C_RXFIFO_TRIGGER_LEVEL (0x20 << 4)
+#define HSI2C_TXFIFO_TRIGGER_LEVEL (0x20 << 16)
+
+/* I2C_TRAILING_CTL Register bits */
+#define HSI2C_TRAILING_COUNT (0xf)
+
+/* I2C_INT_EN Register bits */
+#define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0)
+#define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1)
+#define HSI2C_INT_TRAILING_EN (1u << 6)
+#define HSI2C_INT_I2C_EN (1u << 9)
+
+/* I2C_FIFO_STAT Register bits */
+#define HSI2C_TX_FIFO_LEVEL_MASK (0x7 << 7)
+#define HSI2C_TX_FIFO_FULL (1u << 7)
+#define HSI2C_TX_FIFO_EMPTY (1u << 8)
+#define HSI2C_RX_FIFO_LEVEL_MASK (0x7 << 16)
+#define HSI2C_RX_FIFO_FULL (1u << 23)
+#define HSI2C_RX_FIFO_EMPTY (1u << 24)
+
+/* I2C_CONF Register bits */
+#define HSI2C_HS_MODE (1u << 29)
+#define HSI2C_10BIT_ADDR_MODE (1u << 30)
+#define HSI2C_AUTO_MODE (1u << 31)
+
+/* I2C_AUTO_CONF Register bits */
+#define HSI2C_READ_WRITE (1u << 16)
+#define HSI2C_STOP_AFTER_TRANS (1u << 17)
+#define HSI2C_MASTER_RUN (1u << 31)
+
+/* I2C_TIMEOUT Register bits */
+#define HSI2C_TIMEOUT_EN (1u << 31)
+
+/* I2C_TRANS_STATUS register bits */
+#define HSI2C_TRANS_DONE (1u << 0)
+#define HSI2C_TRANS_ABORT (1u << 1)
+#define HSI2C_NO_DEV_ACK (1u << 2)
+#define HSI2C_NO_DEV (1u << 3)
+#define HSI2C_SLAVE_BUSY (1u << 16)
+#define HSI2C_MASTER_BUSY (1u << 17)
+
+/* I2C_ADDR register bits */
+#define HSI2C_SLV_ADDR_SLV(x) ((x & 0x3ff) << 0)
+#define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10)
+#define HSI2C_MASTER_ID(x) ((x & 0xff) << 24)
+
+/**
+ * Although exynos5 supports max HS-IIC speed of 3.4Mhz,
+ * but currently we are facing booting issues beyond 2.5Mhz
+ * So limiting HS-IIC bus speed to 2.5Mhz
+*/
+#define HSI2C_HS_TX_CLOCK 2500000
+#define HSI2C_FS_TX_CLOCK 400000
+#define HSI2C_HIGH_SPD 1
+#define HSI2C_FAST_SPD 0
+
+#define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000))
+
+/* timeout for pm runtime autosuspend */
+#define EXYNOS5_I2C_PM_TIMEOUT 1000 /* ms */
+
+struct exynos5_i2c {
+ struct i2c_adapter adap;
+ unsigned int suspended:1;
+
+ struct i2c_msg *msg;
+ struct completion msg_complete;
+ unsigned int msg_ptr;
+
+ unsigned int irq;
+
+ void __iomem *regs;
+ struct clk *clk;
+ struct device *dev;
+ int gpios[2];
+ unsigned int clock;
+
+ int status;
+ unsigned int bus_num;
+ int speed_mode;
+};
+
+static const struct of_device_id exynos5_i2c_match[] = {
+ { .compatible = "samsung,exynos5-hsi2c" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
+
+static inline void exynos5_i2c_stop(struct exynos5_i2c *i2c)
+{
+ writel(0, i2c->regs + HSI2C_INT_ENABLE);
+ writel(HSI2C_FUNC_MODE_I2C, i2c->regs + HSI2C_CTL);
+
+ complete(&i2c->msg_complete);
+}
+
+static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c);
+
+static void exynos5_i2c_init(struct exynos5_i2c *i2c)
+{
+ unsigned long i2c_conf = readl(i2c->regs + HSI2C_CONF);
+
+ writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL);
+
+ /* Configure I2C controller in High speed mode */
+ if (i2c->speed_mode == HSI2C_HIGH_SPD)
+ i2c_conf |= HSI2C_HS_MODE;
+
+ writel(i2c_conf, i2c->regs + HSI2C_CONF);
+
+ exynos5_i2c_set_timing(i2c);
+}
+
+static void exynos5_i2c_reset(struct exynos5_i2c *i2c)
+{
+ unsigned long usi_ctl;
+
+ usi_ctl = readl(i2c->regs + HSI2C_CTL);
+ usi_ctl |= HSI2C_SW_RST;
+ writel(usi_ctl, i2c->regs + HSI2C_CTL);
+
+ usi_ctl = readl(i2c->regs + HSI2C_CTL);
+ usi_ctl &= ~HSI2C_SW_RST;
+ writel(usi_ctl, i2c->regs + HSI2C_CTL);
+
+ exynos5_i2c_init(i2c);
+}
+
+static void exynos5_i2c_en_timeout(struct exynos5_i2c *i2c)
+{
+ unsigned long i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
+
+ /* Clear to enable Timeout */
+ i2c_timeout &= ~HSI2C_TIMEOUT_EN;
+ writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
+}
+
+static void exynos5_i2c_master_run(struct exynos5_i2c *i2c)
+{
+ /* Start data transfer in Master mode */
+ u32 i2c_auto_conf = readl(i2c->regs + HSI2C_AUTO_CONF);
+ i2c_auto_conf |= HSI2C_MASTER_RUN;
+ writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
+}
+
+/**
+ * exynos5_i2c_irq: top level IRQ servicing routine
+*/
+static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
+{
+ struct exynos5_i2c *i2c = dev_id;
+ unsigned char byte;
+ u32 t_stat = readl(i2c->regs + HSI2C_TRANS_STATUS);
+
+ i2c->status = -ENXIO;
+ if (t_stat & HSI2C_TRANS_DONE) {
+ i2c->status = 0;
+ if (i2c->msg->flags & I2C_M_RD) {
+ while ((readl(i2c->regs + HSI2C_FIFO_STATUS) &
+ HSI2C_RX_FIFO_FULL) == 0) {
+ byte = (unsigned char)
+ readl(i2c->regs + HSI2C_RX_DATA);
+ i2c->msg->buf[i2c->msg_ptr++] = byte;
+
+ if (i2c->msg->len == 1)
+ break;
+ }
+
+ if (i2c->msg_ptr >= i2c->msg->len)
+ exynos5_i2c_stop(i2c);
+ } else {
+ byte = i2c->msg->buf[i2c->msg_ptr++];
+ writel(byte, i2c->regs + HSI2C_TX_DATA);
+
+ if (i2c->msg_ptr >= i2c->msg->len)
+ exynos5_i2c_stop(i2c);
+ }
+ } else if (t_stat & HSI2C_NO_DEV) {
+ dev_dbg(i2c->dev, "No device found. returning -ENXIO");
+ exynos5_i2c_stop(i2c);
+ goto out;
+ } else if (t_stat & HSI2C_NO_DEV_ACK &&
+ !(i2c->msg->flags & I2C_M_IGNORE_NAK)) {
+ dev_dbg(i2c->dev, "No device Ack. returning -ENXIO");
+ exynos5_i2c_stop(i2c);
+ goto out;
+ } else if (t_stat & HSI2C_TRANS_ABORT) {
+ /* deal with arbitration loss */
+ dev_err(i2c->dev, "deal with arbitration loss\n");
+ exynos5_i2c_stop(i2c);
+ goto out;
+ }
+
+ out:
+ /* Set these bits to clear them */
+ writel(readl(i2c->regs + HSI2C_INT_STATUS),
+ i2c->regs + HSI2C_INT_STATUS);
+ return IRQ_HANDLED;
+}
+
+static void exynos5_i2c_message_start(struct exynos5_i2c *i2c,
+ struct i2c_msg *msgs, int stop)
+{
+ unsigned long usi_ctl = (HSI2C_FUNC_MODE_I2C | HSI2C_MASTER);
+ unsigned long i2c_auto_conf;
+ unsigned long usi_int_en = HSI2C_INT_I2C_EN;
+ unsigned long usi_fifo_ctl;
+
+ exynos5_i2c_en_timeout(i2c);
+
+ /* Set default trigger level for TXFIFO and RXFIFO */
+ usi_fifo_ctl = HSI2C_TXFIFO_TRIGGER_LEVEL | HSI2C_RXFIFO_TRIGGER_LEVEL;
+ /* Enable RXFIFO and TXFIFO */
+ usi_fifo_ctl |= (HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN);
+ writel(usi_fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
+
+ if (msgs->flags & I2C_M_RD) {
+ usi_ctl |= HSI2C_RXCHON;
+
+ i2c_auto_conf |= HSI2C_READ_WRITE;
+
+ usi_int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
+ HSI2C_INT_TRAILING_EN);
+ } else {
+ usi_ctl |= HSI2C_TXCHON;
+
+ i2c_auto_conf &= ~HSI2C_READ_WRITE;
+
+ usi_int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
+ }
+
+ if (stop == 1)
+ i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
+ else
+ i2c_auto_conf &= ~HSI2C_STOP_AFTER_TRANS;
+
+ writel(HSI2C_SLV_ADDR_MAS(msgs->addr), i2c->regs + HSI2C_ADDR);
+
+ writel(usi_ctl, i2c->regs + HSI2C_CTL);
+
+ i2c_auto_conf |= i2c->msg->len;
+ writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
+
+ exynos5_i2c_master_run(i2c);
+
+ /* Enable appropriate interrupts */
+ writel(usi_int_en, i2c->regs + HSI2C_INT_ENABLE);
+}
+
+static int exynos5_i2c_doxfer(struct exynos5_i2c *i2c,
+ struct i2c_msg *msgs, int stop)
+{
+ unsigned long timeout;
+ unsigned long trans_status;
+ unsigned long usi_fifo_stat;
+ int ret = -EAGAIN;
+
+ if (i2c->suspended) {
+ dev_err(i2c->dev, "HS-I2C is suspended.\n");
+ return -EIO;
+ }
+
+ i2c->msg = msgs;
+ i2c->msg_ptr = 0;
+
+ exynos5_i2c_message_start(i2c, msgs, stop);
+
+ timeout = wait_for_completion_interruptible_timeout
+ (&i2c->msg_complete, EXYNOS5_I2C_TIMEOUT);
+
+ if (i2c->status == -ENXIO) {
+ return i2c->status;
+
+ if (timeout == 0) {
+ exynos5_i2c_reset(i2c);
+ if (msgs->flags & I2C_M_RD) {
+ dev_warn(i2c->dev, "rx timeout\n");
+ ret = 0;
+ } else
+ dev_warn(i2c->dev, "tx timeout\n");
+
+ return ret;
+ }
+
+ timeout = jiffies + timeout;
+ while (time_after(timeout, jiffies)) {
+ usi_fifo_stat = readl(i2c->regs + HSI2C_FIFO_STATUS);
+ trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
+ if ((usi_fifo_stat &
+ (HSI2C_TX_FIFO_EMPTY | HSI2C_RX_FIFO_FULL)) &&
+ ((trans_status == 0) || ((stop == 0) &&
+ (trans_status & HSI2C_MASTER_BUSY)))) {
+ ret = 0;
+ break;
+ }
+ }
+
+ if (ret == -EAGAIN) {
+ exynos5_i2c_reset(i2c);
+ dev_warn(i2c->dev, "xfer timeout\n");
+ return ret;
+ }
+
+ return ret;
+}
+
+static int exynos5_i2c_xfer(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ struct exynos5_i2c *i2c = (struct exynos5_i2c *)adap->algo_data;
+ int retry, i;
+ int ret;
+ int stop = 0;
+ struct i2c_msg *msgs_ptr = msgs;
+
+ ret = pm_runtime_get_sync(i2c->dev);
+ if (IS_ERR_VALUE(ret))
+ goto out;
+
+ clk_prepare_enable(i2c->clk);
+
+ for (retry = 0; retry < adap->retries; retry++) {
+ for (i = 0; i < num; i++) {
+ if (i == num - 1)
+ stop = 1;
+ ret = exynos5_i2c_doxfer(i2c, msgs, stop);
+ msgs_ptr++;
+
+ if (ret == -EAGAIN) {
+ msgs_ptr = msgs;
+ stop = 0;
+ break;
+ }
+ }
+
+ if (i == num) {
+ if (ret != -ENXIO)
+ ret = num;
+ goto out;
+
+ }
+
+ dev_dbg(i2c->dev, "retrying transfer (%d)\n", retry);
+
+ udelay(100);
+ }
+
+ ret = -EREMOTEIO;
+ out:
+ clk_disable_unprepare(i2c->clk);
+
+ pm_runtime_mark_last_busy(i2c->dev);
+ pm_runtime_put_autosuspend(i2c->dev);
+ return ret;
+}
+
+static u32 exynos5_i2c_func(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm exynos5_i2c_algorithm = {
+ .master_xfer = exynos5_i2c_xfer,
+ .functionality = exynos5_i2c_func,
+};
+
+static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c)
+{
+ unsigned long i2c_timing_s1;
+ unsigned long i2c_timing_s2;
+ unsigned long i2c_timing_s3;
+ unsigned long i2c_timing_sla;
+ unsigned int op_clk = i2c->clock;
+ unsigned int clkin = clk_get_rate(i2c->clk);
+ unsigned int n_clkdiv;
+ unsigned int t_start_su, t_start_hd;
+ unsigned int t_stop_su;
+ unsigned int t_data_su, t_data_hd;
+ unsigned int t_scl_l, t_scl_h;
+ unsigned int t_sr_release;
+ unsigned int t_ftl_cycle;
+ unsigned int i = 0, utemp0 = 0, utemp1 = 0, utemp2 = 0;
+
+ /* FPCLK / FI2C =
+ * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
+ * uTemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
+ * uTemp1 = (TSCLK_L + TSCLK_H + 2)
+ * uTemp2 = TSCLK_L + TSCLK_H
+ */
+ t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
+ utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
+
+ /* CLK_DIV max is 256 */
+ for (i = 0; i < 256; i++) {
+ utemp1 = utemp0 / (i + 1);
+ /* SCLK_L/H max is 256 / 2 */
+ if (utemp1 < 128) {
+ utemp2 = utemp1 - 2;
+ break;
+ }
+ }
+
+ n_clkdiv = i;
+ t_scl_l = utemp2 / 2;
+ t_scl_h = utemp2 / 2;
+ t_start_su = t_scl_l;
+ t_start_hd = t_scl_l;
+ t_stop_su = t_scl_l;
+ t_data_su = t_scl_l / 2;
+ t_data_hd = t_scl_l / 2;
+ t_sr_release = utemp2;
+
+ i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
+ i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
+ i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
+ i2c_timing_sla = t_data_hd << 0;
+
+ dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
+ t_start_su, t_start_hd, t_stop_su);
+ dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
+ t_data_su, t_scl_l, t_scl_h);
+ dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
+ n_clkdiv, t_sr_release);
+ dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
+
+ if (i2c->speed_mode == HSI2C_HIGH_SPD) {
+ writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
+ writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
+ writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
+ } else {
+ writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
+ writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
+ writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
+ }
+ writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
+
+ return 0;
+}
+
+/**
+ * Parse a list of GPIOs from a node property and request each one
+ *
+ * @param i2c i2c driver data
+ * @return 0 on success, -EINVAL on error, in which case no GPIOs requested
+*/
+static int exynos5_i2c_parse_dt_gpio(struct exynos5_i2c *i2c)
+{
+ int idx, gpio, ret;
+
+ for (idx = 0; idx < 2; idx++) {
+ gpio = of_get_gpio(i2c->dev->of_node, idx);
+ if (!gpio_is_valid(gpio)) {
+ dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio);
+ return -EINVAL;
+ }
+ i2c->gpios[idx] = gpio;
+
+ ret = devm_gpio_request(i2c->dev, gpio, "i2c-bus");
+ if (ret) {
+ dev_err(i2c->dev, "gpio [%d] request failed\n", gpio);
+ return -EINVAL;
+ }
+ }
+ return 0;
+}
+
+
+#define HSI2C_REG(regname) {.name = #regname, .offset = regname}
+static struct debugfs_reg32 exynos5_hsi2c_regs[] = {
+ HSI2C_REG(HSI2C_CTL), HSI2C_REG(HSI2C_FIFO_CTL),
+ HSI2C_REG(HSI2C_TRAILIG_CTL), HSI2C_REG(HSI2C_CLK_CTL),
+ HSI2C_REG(HSI2C_CLK_SLOT), HSI2C_REG(HSI2C_INT_ENABLE),
+ HSI2C_REG(HSI2C_INT_STATUS), HSI2C_REG(HSI2C_ERR_STATUS),
+ HSI2C_REG(HSI2C_FIFO_STATUS), HSI2C_REG(HSI2C_TX_DATA),
+ HSI2C_REG(HSI2C_RX_DATA), HSI2C_REG(HSI2C_CONF),
+ HSI2C_REG(HSI2C_AUTO_CONF), HSI2C_REG(HSI2C_TIMEOUT),
+ HSI2C_REG(HSI2C_MANUAL_CMD), HSI2C_REG(HSI2C_TRANS_STATUS),
+ HSI2C_REG(HSI2C_TIMING_HS1), HSI2C_REG(HSI2C_TIMING_HS2),
+ HSI2C_REG(HSI2C_TIMING_HS3), HSI2C_REG(HSI2C_TIMING_FS1),
+ HSI2C_REG(HSI2C_TIMING_FS2), HSI2C_REG(HSI2C_TIMING_FS3),
+ HSI2C_REG(HSI2C_TIMING_SLA), HSI2C_REG(HSI2C_ADDR),
+};
+
+static struct debugfs_regset32 exynos5_hsi2c_regset = {
+ .regs = exynos5_hsi2c_regs,
+ .nregs = ARRAY_SIZE(exynos5_hsi2c_regs),
+};
+
+static struct dentry *exynos5_hsi2c_reg_debugfs;
+
+static int exynos5_i2c_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct exynos5_i2c *i2c;
+ int ret;
+
+ if (!np) {
+ dev_err(&pdev->dev, "no device node\n");
+ return -ENOENT;
+ }
+
+ i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
+ if (!i2c) {
+ dev_err(&pdev->dev, "no memory for state\n");
+ return -ENOMEM;
+ }
+
+ i2c->bus_num = -1;
+
+ /* Mode of operation High/Fast Speed mode */
+ if (!of_property_read_u32(np, "samsung,hs-mode", &i2c->speed_mode)) {
+ if (of_property_read_u32(np, "samsung,hs-clock", &i2c->clock))
+ i2c->clock = HSI2C_HS_TX_CLOCK;
+ } else {
+ if (of_property_read_u32(np, "samsung,fs-clock", &i2c->clock))
+ i2c->clock = HSI2C_FS_TX_CLOCK;
+ }
+
+ strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name));
+ i2c->adap.owner = THIS_MODULE;
+ i2c->adap.algo = &exynos5_i2c_algorithm;
+ i2c->adap.retries = 2;
+ i2c->adap.class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
+
+ i2c->dev = &pdev->dev;
+ i2c->clk = devm_clk_get(&pdev->dev, "hsi2c");
+ if (IS_ERR(i2c->clk)) {
+ dev_err(&pdev->dev, "cannot get HS-I2C clock\n");
+ ret = -ENOENT;
+ goto err_noclk;
+ }
+
+ dev_dbg(&pdev->dev, "clock source %p\n", i2c->clk);
+
+ clk_prepare_enable(i2c->clk);
+
+ i2c->regs = of_iomap(np, 0);
+ if (!i2c->regs) {
+ dev_err(&pdev->dev, "cannot map HS-I2C IO\n");
+ ret = -ENXIO;
+ goto err_clk;
+ }
+
+ /* parse device tree and inititalise the gpio */
+ if (exynos5_i2c_parse_dt_gpio(i2c))
+ return -EINVAL;
+
+ i2c->irq = irq_of_parse_and_map(np, 0);
+ if (i2c->irq) {
+ ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
+ 0, dev_name(&pdev->dev), i2c);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n",
+ i2c->irq);
+ goto err_iomap;
+ }
+ }
+
+ /*
+ * TODO: Use private lock to avoid race conditions as
+ * mentioned in pm_runtime.txt
+ */
+ pm_runtime_enable(i2c->dev);
+ pm_runtime_set_autosuspend_delay(i2c->dev, EXYNOS5_I2C_PM_TIMEOUT);
+ pm_runtime_use_autosuspend(i2c->dev);
+
+ ret = pm_runtime_get_sync(i2c->dev);
+ if (IS_ERR_VALUE(ret))
+ goto err_iomap;
+
+ exynos5_i2c_init(i2c);
+
+ i2c->adap.algo_data = i2c;
+ i2c->adap.dev.parent = &pdev->dev;
+ i2c->adap.nr = i2c->bus_num;
+ i2c->adap.dev.of_node = np;
+
+ ret = i2c_add_numbered_adapter(&i2c->adap);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to add bus to i2c core\n");
+ goto err_pm;
+ }
+
+ init_completion(&i2c->msg_complete);
+ of_i2c_register_devices(&i2c->adap);
+ platform_set_drvdata(pdev, i2c);
+
+ exynos5_hsi2c_reg_debugfs = debugfs_create_regset32("exynos5-hsi2c",
+ S_IFREG | S_IRUGO,
+ NULL, &exynos5_hsi2c_regset);
+ clk_disable_unprepare(i2c->clk);
+ pm_runtime_mark_last_busy(i2c->dev);
+ pm_runtime_put_autosuspend(i2c->dev);
+ return 0;
+
+ err_pm:
+ pm_runtime_put(i2c->dev);
+ pm_runtime_disable(&pdev->dev);
+ err_iomap:
+ iounmap(i2c->regs);
+ err_clk:
+ clk_disable_unprepare(i2c->clk);
+ err_noclk:
+ return ret;
+}
+
+static int exynos5_i2c_remove(struct platform_device *pdev)
+{
+ struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = pm_runtime_get_sync(&pdev->dev);
+ if (IS_ERR_VALUE(ret))
+ return ret;
+
+ clk_disable_unprepare(i2c->clk);
+ pm_runtime_put(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+
+ i2c_del_adapter(&i2c->adap);
+
+ iounmap(i2c->regs);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int exynos5_i2c_suspend_noirq(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+
+ i2c->suspended = 1;
+
+ return 0;
+}
+
+static int exynos5_i2c_resume_noirq(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
+
+ clk_prepare_enable(i2c->clk);
+ exynos5_i2c_init(i2c);
+ clk_disable_unprepare(i2c->clk);
+ i2c->suspended = 0;
+
+ return 0;
+}
+
+static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
+ .suspend_noirq = exynos5_i2c_suspend_noirq,
+ .resume_noirq = exynos5_i2c_resume_noirq,
+};
+
+#define EXYNOS5_DEV_PM_OPS (&exynos5_i2c_dev_pm_ops)
+#else
+#define EXYNOS5_DEV_PM_OPS NULL
+#endif
+
+static struct platform_driver exynos5_i2c_driver = {
+ .probe = exynos5_i2c_probe,
+ .remove = exynos5_i2c_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "exynos5-hsi2c",
+ .pm = EXYNOS5_DEV_PM_OPS,
+ .of_match_table = of_match_ptr(exynos5_i2c_match),
+ },
+};
+
+static int __init i2c_adap_exynos5_init(void)
+{
+ return platform_driver_register(&exynos5_i2c_driver);
+}
+subsys_initcall(i2c_adap_exynos5_init);
+
+static void __exit i2c_adap_exynos5_exit(void)
+{
+ platform_driver_unregister(&exynos5_i2c_driver);
+}
+module_exit(i2c_adap_exynos5_exit);
+
+MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
+MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>");
+MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>");
+MODULE_LICENSE("GPL");
--
1.7.9.5


\
 
 \ /
  Last update: 2013-02-01 17:43    [W:0.400 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site