lkml.org 
[lkml]   [2013]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 9/9] ARM: pxa27x: device tree support ICP DAS LP-8x4x
Date
On Sunday 08 December 2013, Sergei Ianovich wrote:
> +
> +#ifdef CONFIG_PXA27x
> +extern void __init pxa27x_dt_init_irq(void);

This is not the right place to put an 'extern' declaration, it should go into
a header file if it's really needed. Ideally you would not need it at all
and just add an IRQCHIP_DECLARE() line into the driver to automatically
probe it.

> +static const struct of_dev_auxdata pxa27x_auxdata_lookup[] __initconst = {
> + OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40100000, "pxa2xx-uart.0", NULL),
> + OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40200000, "pxa2xx-uart.1", NULL),
> + OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40700000, "pxa2xx-uart.2", NULL),
> + OF_DEV_AUXDATA("mrvl,pxa-uart", 0x41600000, "pxa2xx-uart.3", NULL),
> + OF_DEV_AUXDATA("marvell,pxa-mmc", 0x41100000, "pxa2xx-mci.0", NULL),
> + OF_DEV_AUXDATA("intel,pxa27x-gpio", 0x40e00000, "pxa27x-gpio", NULL),
> + OF_DEV_AUXDATA("marvell,pxa-ohci", 0x4c000000, "pxa27x-ohci", NULL),
> + OF_DEV_AUXDATA("mrvl,pxa-i2c", 0x40301680, "pxa2xx-i2c.0", NULL),
> + {}
> +};

I guess these are needed only for clock management purposes at the moment?

> +static void __init pxa27x_init_early(void)
> +{
> + pxa27x_skip_init();
> +}

I would prefer not to have an init_early function at all, and instead
check "if (of_have_populated_dt())" in pxa27x_init, or to split
that function into two.

> +static const char *pxa27x_dt_board_compat[] __initdata = {
> + "marvell,pxa27x",
> + NULL,
> +};
> +
> +#ifdef CONFIG_MACH_LP8X4X
> +static const char *lp8x4x_dt_board_compat[] __initdata = {
> + "marvell,lp8x4x",
> + NULL,
> +};

Note that you should not have wildcards in any "compatible" strings.
Just list all the combinations here (pxa270, pxa271, pxa272, and whatever
you need for lp8x4x).

> +static void lp8x4x_restart(enum reboot_mode mode, const char *cmd)
> +{
> + /* Switch off fast-bus and turbo mode */
> + asm volatile("mcr p14, 0, %0, c6, c0, 0" : :
> + "r"(2));
> + /* SDRAM hangs on watchdog reset on Marvell PXA270 (erratum 71) */
> + pxa_restart(REBOOT_SOFT, cmd);
> +}
> +#endif
> +#endif

Since the only difference here is the restart logic, I would prefer here to
have only a single DT_MACHINE_START() and do

static void pxa27x_restart(enum reboot_mode mode, const char *cmd)
{
/* Switch off fast-bus and turbo mode */
if (of_machine_is_compatible("marvell,lp8x4x"))
asm volatile("mcr p14, 0, %0, c6, c0, 0" : : "r"(2));

/* SDRAM hangs on watchdog reset on Marvell PXA270 (erratum 71) */
if (of_machine_is_compatible("marvell,pxa270"))
pxa_restart(REBOOT_SOFT, cmd);
}

Arnd


\
 
 \ /
  Last update: 2013-12-09 03:01    [W:0.377 / U:0.776 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site