lkml.org 
[lkml]   [2013]   [Dec]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 01/10] net: stmmac: Enable stmmac main clock when probing hardware
    Date
    Signed-off-by: Chen-Yu Tsai <wens@csie.org>
    ---

    Guiseppe previously stated that the "stmmaceth" clock is the
    main clock that drives the IP. The stmmac driver does not
    enable this clock during the probe phase. When the driver is
    built in to the kernel, this is fine because the clock maybe
    on by default, or the boot loader had enabled it.

    If stmmac is built as a module, when the module is loaded,
    the clock may be found unused and disabled by the kernel.

    drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 24 +++++++++++++----------
    1 file changed, 14 insertions(+), 10 deletions(-)

    diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
    index 8d4ccd3..7da71ed 100644
    --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
    +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
    @@ -2688,10 +2688,17 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
    if ((phyaddr >= 0) && (phyaddr <= 31))
    priv->plat->phy_addr = phyaddr;

    + priv->stmmac_clk = clk_get(priv->device, STMMAC_RESOURCE_NAME);
    + if (IS_ERR(priv->stmmac_clk)) {
    + pr_warn("%s: warning: cannot get CSR clock\n", __func__);
    + goto error_clk_get;
    + }
    + clk_prepare_enable(priv->stmmac_clk);
    +
    /* Init MAC and get the capabilities */
    ret = stmmac_hw_init(priv);
    if (ret)
    - goto error_free_netdev;
    + goto error_hw_init;

    ndev->netdev_ops = &stmmac_netdev_ops;

    @@ -2729,12 +2736,6 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
    goto error_netdev_register;
    }

    - priv->stmmac_clk = clk_get(priv->device, STMMAC_RESOURCE_NAME);
    - if (IS_ERR(priv->stmmac_clk)) {
    - pr_warn("%s: warning: cannot get CSR clock\n", __func__);
    - goto error_clk_get;
    - }
    -
    /* If a specific clk_csr value is passed from the platform
    * this means that the CSR Clock Range selection cannot be
    * changed at run-time and it is fixed. Viceversa the driver'll try to
    @@ -2759,15 +2760,18 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
    }
    }

    + clk_disable_unprepare(priv->stmmac_clk);
    +
    return priv;

    error_mdio_register:
    - clk_put(priv->stmmac_clk);
    -error_clk_get:
    unregister_netdev(ndev);
    error_netdev_register:
    netif_napi_del(&priv->napi);
    -error_free_netdev:
    +error_hw_init:
    + clk_disable_unprepare(priv->stmmac_clk);
    + clk_put(priv->stmmac_clk);
    +error_clk_get:
    free_netdev(ndev);

    return NULL;
    --
    1.8.5.1


    \
     
     \ /
      Last update: 2013-12-06 19:41    [W:4.021 / U:0.040 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site