lkml.org 
[lkml]   [2013]   [Dec]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] staging: octeon-usb: Probe via device tree populated platform device.
Hi,

On Tue, Dec 03, 2013 at 11:46:52AM -0800, David Daney wrote:
> From: David Daney <david.daney@cavium.com>
>
> Extract clocking parameters from the device tree, and remove now dead
> code and types.
>
> Signed-off-by: David Daney <david.daney@cavium.com>

Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>

Thanks,

A.

> ---
> drivers/staging/octeon-usb/octeon-hcd.c | 273 ++++++++++++++------------------
> 1 file changed, 116 insertions(+), 157 deletions(-)
>
> diff --git a/drivers/staging/octeon-usb/octeon-hcd.c b/drivers/staging/octeon-usb/octeon-hcd.c
> index d118952..c53499a 100644
> --- a/drivers/staging/octeon-usb/octeon-hcd.c
> +++ b/drivers/staging/octeon-usb/octeon-hcd.c
> @@ -275,13 +275,6 @@ enum cvmx_usb_pipe_flags {
> */
> #define MAX_TRANSFER_PACKETS ((1<<10)-1)
>
> -enum {
> - USB_CLOCK_TYPE_REF_12,
> - USB_CLOCK_TYPE_REF_24,
> - USB_CLOCK_TYPE_REF_48,
> - USB_CLOCK_TYPE_CRYSTAL_12,
> -};
> -
> /**
> * Logical transactions may take numerous low level
> * transactions, especially when splits are concerned. This
> @@ -471,19 +464,6 @@ struct octeon_hcd {
> /* Returns the IO address to push/pop stuff data from the FIFOs */
> #define USB_FIFO_ADDRESS(channel, usb_index) (CVMX_USBCX_GOTGCTL(usb_index) + ((channel)+1)*0x1000)
>
> -static int octeon_usb_get_clock_type(void)
> -{
> - switch (cvmx_sysinfo_get()->board_type) {
> - case CVMX_BOARD_TYPE_BBGW_REF:
> - case CVMX_BOARD_TYPE_LANAI2_A:
> - case CVMX_BOARD_TYPE_LANAI2_U:
> - case CVMX_BOARD_TYPE_LANAI2_G:
> - case CVMX_BOARD_TYPE_UBNT_E100:
> - return USB_CLOCK_TYPE_CRYSTAL_12;
> - }
> - return USB_CLOCK_TYPE_REF_48;
> -}
> -
> /**
> * Read a USB 32bit CSR. It performs the necessary address swizzle
> * for 32bit CSRs and logs the value in a readable format if
> @@ -582,37 +562,6 @@ static inline int __cvmx_usb_get_data_pid(struct cvmx_usb_pipe *pipe)
> return 0; /* Data0 */
> }
>
> -
> -/**
> - * Return the number of USB ports supported by this Octeon
> - * chip. If the chip doesn't support USB, or is not supported
> - * by this API, a zero will be returned. Most Octeon chips
> - * support one usb port, but some support two ports.
> - * cvmx_usb_initialize() must be called on independent
> - * struct cvmx_usb_state.
> - *
> - * Returns: Number of port, zero if usb isn't supported
> - */
> -static int cvmx_usb_get_num_ports(void)
> -{
> - int arch_ports = 0;
> -
> - if (OCTEON_IS_MODEL(OCTEON_CN56XX))
> - arch_ports = 1;
> - else if (OCTEON_IS_MODEL(OCTEON_CN52XX))
> - arch_ports = 2;
> - else if (OCTEON_IS_MODEL(OCTEON_CN50XX))
> - arch_ports = 1;
> - else if (OCTEON_IS_MODEL(OCTEON_CN31XX))
> - arch_ports = 1;
> - else if (OCTEON_IS_MODEL(OCTEON_CN30XX))
> - arch_ports = 1;
> - else
> - arch_ports = 0;
> -
> - return arch_ports;
> -}
> -
> /**
> * Initialize a USB port for use. This must be called before any
> * other access to the Octeon USB port is made. The port starts
> @@ -628,41 +577,16 @@ static int cvmx_usb_get_num_ports(void)
> * Returns: 0 or a negative error code.
> */
> static int cvmx_usb_initialize(struct cvmx_usb_state *usb,
> - int usb_port_number)
> + int usb_port_number,
> + enum cvmx_usb_initialize_flags flags)
> {
> union cvmx_usbnx_clk_ctl usbn_clk_ctl;
> union cvmx_usbnx_usbp_ctl_status usbn_usbp_ctl_status;
> - enum cvmx_usb_initialize_flags flags = 0;
> int i;
>
> /* At first allow 0-1 for the usb port number */
> if ((usb_port_number < 0) || (usb_port_number > 1))
> return -EINVAL;
> - /* For all chips except 52XX there is only one port */
> - if (!OCTEON_IS_MODEL(OCTEON_CN52XX) && (usb_port_number > 0))
> - return -EINVAL;
> - /* Try to determine clock type automatically */
> - if (octeon_usb_get_clock_type() == USB_CLOCK_TYPE_CRYSTAL_12) {
> - /* Only 12 MHZ crystals are supported */
> - flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_XI;
> - } else {
> - flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND;
> -
> - switch (octeon_usb_get_clock_type()) {
> - case USB_CLOCK_TYPE_REF_12:
> - flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ;
> - break;
> - case USB_CLOCK_TYPE_REF_24:
> - flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ;
> - break;
> - case USB_CLOCK_TYPE_REF_48:
> - flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ;
> - break;
> - default:
> - return -EINVAL;
> - break;
> - }
> - }
>
> memset(usb, 0, sizeof(*usb));
> usb->init_flags = flags;
> @@ -3431,7 +3355,6 @@ static int octeon_usb_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
> return 0;
> }
>
> -
> static const struct hc_driver octeon_hc_driver = {
> .description = "Octeon USB",
> .product_desc = "Octeon Host Controller",
> @@ -3448,15 +3371,74 @@ static const struct hc_driver octeon_hc_driver = {
> .hub_control = octeon_usb_hub_control,
> };
>
> -
> -static int octeon_usb_driver_probe(struct device *dev)
> +static int octeon_usb_probe(struct platform_device *pdev)
> {
> int status;
> - int usb_num = to_platform_device(dev)->id;
> - int irq = platform_get_irq(to_platform_device(dev), 0);
> + int initialize_flags;
> + int usb_num;
> + struct resource *res_mem;
> + struct device_node *usbn_node;
> + int irq = platform_get_irq(pdev, 0);
> + struct device *dev = &pdev->dev;
> struct octeon_hcd *priv;
> struct usb_hcd *hcd;
> unsigned long flags;
> + u32 clock_rate = 48000000;
> + bool is_crystal_clock = false;
> + const char *clock_type;
> + int i;
> +
> + if (dev->of_node == NULL) {
> + dev_err(dev, "Error: empty of_node\n");
> + return -ENXIO;
> + }
> + usbn_node = dev->of_node->parent;
> +
> + i = of_property_read_u32(usbn_node,
> + "refclk-frequency", &clock_rate);
> + if (i) {
> + dev_err(dev, "No USBN \"refclk-frequency\"\n");
> + return -ENXIO;
> + }
> + switch (clock_rate) {
> + case 12000000:
> + initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_12MHZ;
> + break;
> + case 24000000:
> + initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_24MHZ;
> + break;
> + case 48000000:
> + initialize_flags = CVMX_USB_INITIALIZE_FLAGS_CLOCK_48MHZ;
> + break;
> + default:
> + dev_err(dev, "Illebal USBN \"refclk-frequency\" %u\n", clock_rate);
> + return -ENXIO;
> +
> + }
> +
> + i = of_property_read_string(usbn_node,
> + "refclk-type", &clock_type);
> +
> + if (!i && strcmp("crystal", clock_type) == 0)
> + is_crystal_clock = true;
> +
> + if (is_crystal_clock)
> + initialize_flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_XI;
> + else
> + initialize_flags |= CVMX_USB_INITIALIZE_FLAGS_CLOCK_XO_GND;
> +
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (res_mem == NULL) {
> + dev_err(dev, "found no memory resource\n");
> + return -ENXIO;
> + }
> + usb_num = (res_mem->start >> 44) & 1;
> +
> + if (irq < 0) {
> + /* Defective device tree, but we know how to fix it. */
> + irq_hw_number_t hwirq = usb_num ? (1 << 6) + 17 : 56;
> + irq = irq_create_mapping(NULL, hwirq);
> + }
>
> /*
> * Set the DMA mask to 64bits so we get buffers already translated for
> @@ -3465,6 +3447,26 @@ static int octeon_usb_driver_probe(struct device *dev)
> dev->coherent_dma_mask = ~0;
> dev->dma_mask = &dev->coherent_dma_mask;
>
> + /*
> + * Only cn52XX and cn56XX have DWC_OTG USB hardware and the
> + * IOB priority registers. Under heavy network load USB
> + * hardware can be starved by the IOB causing a crash. Give
> + * it a priority boost if it has been waiting more than 400
> + * cycles to avoid this situation.
> + *
> + * Testing indicates that a cnt_val of 8192 is not sufficient,
> + * but no failures are seen with 4096. We choose a value of
> + * 400 to give a safety factor of 10.
> + */
> + if (OCTEON_IS_MODEL(OCTEON_CN52XX) || OCTEON_IS_MODEL(OCTEON_CN56XX)) {
> + union cvmx_iob_n2c_l2c_pri_cnt pri_cnt;
> +
> + pri_cnt.u64 = 0;
> + pri_cnt.s.cnt_enb = 1;
> + pri_cnt.s.cnt_val = 400;
> + cvmx_write_csr(CVMX_IOB_N2C_L2C_PRI_CNT, pri_cnt.u64);
> + }
> +
> hcd = usb_create_hcd(&octeon_hc_driver, dev, dev_name(dev));
> if (!hcd) {
> dev_dbg(dev, "Failed to allocate memory for HCD\n");
> @@ -3478,7 +3480,7 @@ static int octeon_usb_driver_probe(struct device *dev)
> tasklet_init(&priv->dequeue_tasklet, octeon_usb_urb_dequeue_work, (unsigned long)priv);
> INIT_LIST_HEAD(&priv->dequeue_list);
>
> - status = cvmx_usb_initialize(&priv->usb, usb_num);
> + status = cvmx_usb_initialize(&priv->usb, usb_num, initialize_flags);
> if (status) {
> dev_dbg(dev, "USB initialization failed with %d\n", status);
> kfree(hcd);
> @@ -3492,21 +3494,22 @@ static int octeon_usb_driver_probe(struct device *dev)
> cvmx_usb_poll(&priv->usb);
> spin_unlock_irqrestore(&priv->lock, flags);
>
> - status = usb_add_hcd(hcd, irq, IRQF_SHARED);
> + status = usb_add_hcd(hcd, irq, 0);
> if (status) {
> dev_dbg(dev, "USB add HCD failed with %d\n", status);
> kfree(hcd);
> return -1;
> }
>
> - dev_dbg(dev, "Registered HCD for port %d on irq %d\n", usb_num, irq);
> + dev_info(dev, "Registered HCD for port %d on irq %d\n", usb_num, irq);
>
> return 0;
> }
>
> -static int octeon_usb_driver_remove(struct device *dev)
> +static int octeon_usb_remove(struct platform_device *pdev)
> {
> int status;
> + struct device *dev = &pdev->dev;
> struct usb_hcd *hcd = dev_get_drvdata(dev);
> struct octeon_hcd *priv = hcd_to_octeon(hcd);
> unsigned long flags;
> @@ -3524,85 +3527,41 @@ static int octeon_usb_driver_remove(struct device *dev)
> return 0;
> }
>
> -static struct device_driver octeon_usb_driver = {
> - .name = "OcteonUSB",
> - .bus = &platform_bus_type,
> - .probe = octeon_usb_driver_probe,
> - .remove = octeon_usb_driver_remove,
> +static struct of_device_id octeon_usb_match[] = {
> + {
> + .compatible = "cavium,octeon-5750-usbc",
> + },
> + {},
> };
>
> +static struct platform_driver octeon_usb_driver = {
> + .driver = {
> + .name = "OcteonUSB",
> + .owner = THIS_MODULE,
> + .of_match_table = octeon_usb_match,
> + },
> + .probe = octeon_usb_probe,
> + .remove = octeon_usb_remove,
> +};
>
> -#define MAX_USB_PORTS 10
> -static struct platform_device *pdev_glob[MAX_USB_PORTS];
> -static int octeon_usb_registered;
> -static int __init octeon_usb_module_init(void)
> +static int __init octeon_usb_driver_init(void)
> {
> - int num_devices = cvmx_usb_get_num_ports();
> - int device;
> -
> - if (usb_disabled() || num_devices == 0)
> - return -ENODEV;
> -
> - if (driver_register(&octeon_usb_driver))
> - return -ENOMEM;
> -
> - octeon_usb_registered = 1;
> -
> - /*
> - * Only cn52XX and cn56XX have DWC_OTG USB hardware and the
> - * IOB priority registers. Under heavy network load USB
> - * hardware can be starved by the IOB causing a crash. Give
> - * it a priority boost if it has been waiting more than 400
> - * cycles to avoid this situation.
> - *
> - * Testing indicates that a cnt_val of 8192 is not sufficient,
> - * but no failures are seen with 4096. We choose a value of
> - * 400 to give a safety factor of 10.
> - */
> - if (OCTEON_IS_MODEL(OCTEON_CN52XX) || OCTEON_IS_MODEL(OCTEON_CN56XX)) {
> - union cvmx_iob_n2c_l2c_pri_cnt pri_cnt;
> -
> - pri_cnt.u64 = 0;
> - pri_cnt.s.cnt_enb = 1;
> - pri_cnt.s.cnt_val = 400;
> - cvmx_write_csr(CVMX_IOB_N2C_L2C_PRI_CNT, pri_cnt.u64);
> - }
> -
> - for (device = 0; device < num_devices; device++) {
> - struct resource irq_resource;
> - struct platform_device *pdev;
> - memset(&irq_resource, 0, sizeof(irq_resource));
> - irq_resource.start = (device == 0) ? OCTEON_IRQ_USB0 : OCTEON_IRQ_USB1;
> - irq_resource.end = irq_resource.start;
> - irq_resource.flags = IORESOURCE_IRQ;
> - pdev = platform_device_register_simple((char *)octeon_usb_driver. name, device, &irq_resource, 1);
> - if (IS_ERR(pdev)) {
> - driver_unregister(&octeon_usb_driver);
> - octeon_usb_registered = 0;
> - return PTR_ERR(pdev);
> - }
> - if (device < MAX_USB_PORTS)
> - pdev_glob[device] = pdev;
> + if (usb_disabled())
> + return 0;
>
> - }
> - return 0;
> + return platform_driver_register(&octeon_usb_driver);
> }
> +module_init(octeon_usb_driver_init);
>
> -static void __exit octeon_usb_module_cleanup(void)
> +static void __exit octeon_usb_driver_exit(void)
> {
> - int i;
> + if (usb_disabled())
> + return;
>
> - for (i = 0; i < MAX_USB_PORTS; i++)
> - if (pdev_glob[i]) {
> - platform_device_unregister(pdev_glob[i]);
> - pdev_glob[i] = NULL;
> - }
> - if (octeon_usb_registered)
> - driver_unregister(&octeon_usb_driver);
> + platform_driver_unregister(&octeon_usb_driver);
> }
> +module_exit(octeon_usb_driver_exit);
>
> MODULE_LICENSE("GPL");
> -MODULE_AUTHOR("Cavium Networks <support@caviumnetworks.com>");
> -MODULE_DESCRIPTION("Cavium Networks Octeon USB Host driver.");
> -module_init(octeon_usb_module_init);
> -module_exit(octeon_usb_module_cleanup);
> +MODULE_AUTHOR("Cavium, Inc. <support@cavium.com>");
> +MODULE_DESCRIPTION("Cavium Inc. OCTEON USB Host driver.");
> --
> 1.7.11.7
>
>


\
 
 \ /
  Last update: 2013-12-04 23:01    [W:0.085 / U:0.944 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site