lkml.org 
[lkml]   [2013]   [Dec]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RFC 1/4] phy: Add new Exynos5 USB 3.0 PHY driver
Hi Vivek,

On Wednesday 20 November 2013 09:14 PM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Wednesday 20 November 2013 03:02 PM, Vivek Gautam wrote:
>> On Wed, Nov 20, 2013 at 2:34 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
>>> On Wednesday 20 November 2013 02:27 PM, Vivek Gautam wrote:
>>>> Hi Kishon,
>>>>
>>>>
>>>> On Mon, Nov 11, 2013 at 4:41 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
>>>>> Hi,
>>>> sorry for the delayed response.
>>>>
>>>>>
>>>>> On Wednesday 06 November 2013 05:37 AM, Jingoo Han wrote:
>>>>>> On Wednesday, November 06, 2013 2:58 AM, Vivek Gautam wrote:
>>>>>>> On Tue, Nov 5, 2013 at 5:33 PM, Jingoo Han <jg1.han@samsung.com> wrote:
>>>>>>
>>>>>> [.....]
>>>>>>
>>>>>>>> USB3.0 PHY consists of two blocks such as 3.0 block and 2.0 block.
>>>>>>>> This USB3.0 PHY can support UTMI+ and PIPE3 interface for 3.0 block
>>>>>>>> and 2.0 block, respectively.
>>>>>>>>
>>>>>>>> Conclusion:
>>>>>>>>
>>>>>>>> 1) USB2.0 PHY: USB2.0 HOST, USB2.0 Device
>>>>>>>> Base address: 0x1213 0000
>>>>>>>>
>>>>>>>> 2) USB3.0 PHY: USB3.0 DRD (3.0 HOST & 3.0 Device)
>>>>>>>> Base address: 0x1210 0000
>>>>>>>> 2.0 block(UTMI+) & 3.0 block(PIPE3)
>>>>>>>
>>>>>>> And this is of course the PHY used by DWC3 controller, which works at
>>>>>>> both High speed as well as Super Speed.
>>>>>>> Right ?
>>>>>>
>>>>>> Right.
>>>>>>
>>>>>> While 3.0 block(PIPE3) can be used for Super Speed, 2.0 block(UTMI+)
>>>>>> can be used for High speed.
>>>>>
>>>>> It should then come under *single IP muliple PHY* category similar to what
>>>>> Sylwester has done.
>>>>
>>>> Do you mean that i should be including PHY IDs for UTMI+ phy and PIPE3
>>>> phy present in this PHY block ?
>>>> AFAICS the two phys (UTMI+ and PIPE3) do not really have separate
>>>> registers to program, and that's the reason
>>>> we program the entire PHY in a shot.
>>>
>>> you mean you program the same set of bits for UTMI+ and PIPE3?
>>
>> No, looking closely into PHY datasheet as well as Exynos5250 manual, i
>> can see that UTMI+ and PIPE3
>> phys have separate bit settings. So i think we should be able to
>> segregate the two PHYs (UTMI+ and PIPE3).
>> Pardon me for my earlier observations.
>
> no problem..
>> Let me clarify more with our h/w team also on this and then i will
>> confirm with this.

Did you get more information on this?

Thanks
Kishon


\
 
 \ /
  Last update: 2013-12-04 16:01    [W:0.139 / U:5.524 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site